Bedienungsanleitung Elica Vogue (Seite 11 von 14) (Englisch)

471230

Zoom out

Zoom in

Vorherige Seite

1/14

Nächste Seite

suction unit.

Installation

The minimum distance between the supporting surface for the

cooking equipment on the hob and the lowest part of the

range hood must be not less than 50cm from electric cookers

and 65cm from gas or mixed cookers.

If the instructions for installation for the gas hob specify a

greater distance, this must be adhered to.

Electrical connection

The mains power supply must correspond to the rating

indicated on the plate situated inside the hood. If provided with

a plug connect the hood to a socket in compliance with current

regulations and positioned in an accessible area. If it not fitted

with a plug (direct mains connection) or if the plug is not

located in an accessible area apply a double pole switch in

accordance with standards which assures the complete

disconnection of the mains under conditions relating to over-

current category III, in accordance with installation

instructions.

Warning! Before re-connecting the hood circuit to the mains

supply and checking the efficient function, always check that

the mains cable is correctly assembled.

Mounting

Before beginning installation:

• Check that the product purchased is of a suitable size for

the chosen installation area.

• To facilitate installation, remove the fat filters and the

other parts allowed and described here, dismantle and

mount it.

To remove see also the relative paragraphs.

• Remove the active carbon (*) filter/s if supplied (see also

relative paragraph). This/these is/are to be mounted only

if you want lo use the hood in the filtering version.

• Check (for transport reasons) that there is no other

supplied material inside the hood (e.g. packets with

screws (*), guarantees (*), etc.), eventually removing

them and keeping them.

• If possible, disconnect and move freestanding or slide-in

range from cabinet opening to provide easier access to

rear wall/ceiling. Otherwise put a thick, protective

covering over countertop, cooktop or range to protect

from damage and debris. Select a flat surface for

assembling the unit. Cover that surface with a protective

covering and place all canopy hood parts and hardware

in it.

• Disconnect the hood during electrical connection, by

turning the home mains switch off.

• In addition check whether near the installation area of the

hood (in the area accessible also with the hood mounted)

an electric socket is available and it is possible to

connect a fumes discharge device to the outside (only

suction version).

• Carry out all the masonry work necessary (e.g.

installation of an electric socket and/or a hole for the

passage of the discharge tube).

Expansion wall plugs are provided to secure the hood to most

types of walls/ceilings. However, a qualified technician must

verify suitability of the materials in accordance with the type of

wall/ceiling. The wall/ceiling must be strong enough to take

the weight of the hood. Do not tile, grout or silicone this

appliance to the wall. Surface mounting only.

Very heavy product; hood handling and installation must

be carried out by at least two people.

Fig. 5

To avoid damage during the extraction of the box, grab the

hood by using the stirrups of the lattice (Picture 5a).

Remove the upper protection support by unscrewing the 2

screws and washers fixed to the lattice.

Remove the lower protection support by unscrewing the 3

screws and washers fixed to the structure of the hood.

To carry out this operation remove the anti-grease filters

(Picture 5b).

Remove the front protection devices fixed to the hood with

adhesive tape (Picture 5c).

Remove the upper covers by unscrewing the 6 screws (3 each

cover) (Picture 5d).

Note: keep the 6 screws removed. They shall be used again

to definitively install the upper covers.

Fig. 6

1. Adjust extension of the hood support structure, as the

final height of the hood depends on this.

Note: In some cases the upper section of the lattice is

fixed to the lower section with one or more screws,

eventually check and remove them temporarily to

allow the adjustment of the support structure.

2. Fix the two sections of the structure with a total of 24

screws (6 per corner).

Fig. 7

3. Apply the drilling template to the ceiling vertically over the

cooking top (the centre of the template should

correspond to the centre of the cooking top and the sides

should be parallel to the sides of the cooking top – the

side of the template with the word FRONT (or with the

arrows) corresponds to the control panel side). Connect

the electricity.

4. Drill as shown (8 holes for 8 wall plugs – 4 plugs for

fixture), screw the outer screws leaving a space of

about 1 cm. between the screw head and the ceiling.

Fig. 8

5. Fit an exhaust pipe inside the truss and connect it to

the motor compartment connection ring (exhaust pipe

and fixing brackets are not supplied).

In case of filter functioning, insert the reducer on the

connecting ring of the motor room (a), connect an

exhaust pipe to the reducer (b), install the deflector F on

the lattice (c) and fix it with 2 screws to the special stirrup

(d), finally connect the exhaust pipe to the connecting

ring placed on the deflector (Picture 8F).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Elica Vogue Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info