Bedienungsanleitung Elica Wave (Seite 21 von 96) (Deutsch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

471196

Zoom out

Zoom in

Vorherige Seite

1/96

Nächste Seite

Mounting

Expansion wall plugs are provided to secure the hood to

most types of walls/ceilings. However, a qualified technician

must verify suitability of the materials in accordance with the

type of wall/ceiling. The wall/ceiling must be strong enough to

take the weight of the hood. Do not tile, grout or silicone

this appliance to the wall. Surface mounting only.

Description of the hood

Fig. 1

H. Interconnection cable

K. Control lever

Attention! The control lever is already supplied. It is to

be installed last, before connecting the hood to the

mains.

Insert the control lever into the apposite housing (see

drawings on the first pages of this booklet - triggered

connection, compulsory direction.

L. Halogen bulb

M. Lateral filter holder frame

N. Active carbon filter

O. Metal anti-fat filter

P. Anti-fat and carbon filters holder frame

Q. Filter holder frame releases

Operation

Use the high suction speed in cases of concentrated kitchen

vapours. It is recommended that the cooker hood suction is

switched on for 5 minutes prior to cooking and to leave in

operation during cooking and for another 15 minutes

approximately after terminating cooking.

The hood is equipped with a “TOUCH” device to control the

lights and speed.

For the correct use please carefully read the intructions below.

The cooker hood can be controlled through a remote control

available as accessory kit (see the paragraph relating to the

functioning of the remote control).

Automatic start-up function

The hood is equipped with a temperature sensor which

activates the motor to the first suction speed (power) in the

event that the room temperature in the surrounding area is

higher than 70°C.

The user may switch off or modify the suction speed (power)

(see paragraph “suction speed (power) control”).

Suction speed (power) control

The suction speed (power) is cyclical depending on the speed

sequence “stand-by – 1-2-3-4- Stand by -1-2-...” therefore

every time the T1 button is pressed on the control panel, the

suction speed (power) is increased by one level, in order to

switch off (stand-by) if the button is pressed again when the

hood is in suction speed (power) 4.

The hood may be switched off (stand-by) while the hood is set

on any speed by holding down the T1 button on the control

panel for a bit longer (more than 3 seconds).

The hood's suction speed (power) may be determined as the

control panel is equipped with a LED light that changes colors

as follows, depending on the suction speed (power):

Hood in stand-by: LED LIGHT SWITCHED OFF

suction speed (power) -GREEN LED LIGHT

suction speed (power) – ORANGE LED LIGHT (amber)

suction speed (power) - RED LED LIGHT

suction speed (power) - RED LED LIGHT (FLASHING)

Note: The 4

suction speed (power) stays on for 5 minutes,

after which the suction motor will position itself on the 2

speed.

If pressed again, the suction motor will switch off (stand-by).

Grease filters need cleaning: FLASHING GREEN LED light

(read instructions found under “Reset and configuration for

filter saturation signal”)

Coal filters must be cleaned or replaced: FLASHING

ORANGE (amber) LED light (read instructions found under

“Reset and configuration for filter saturation signal”)

Note: The reset procedure may be activated by both the

control panel and the remote control.

Center light check

The center light may be switched on and off by pressing the

T2 button on the control panel.

Side light check (when scheduled)

The side lights may be switched on and off by pressing AND

HOLDING DOWN the T2 button on the control panel.

HOLDING DOWN the button, besides permitting to switch the

hood on and off, it also regulates the light intensity given from

the lights.

Note: The switching on and off functions (and regulating

function) alternate.

The regulation of the light intensity is not available for hoods

with neon lights.

Reset and configuration for filter saturation signal

Switch on hood to any speed (see above paragraph “Suction

speed (power) selection”)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Elica Wave Seite 21

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Elica Wave

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info