Bedienungsanleitung Elite Arion (Seite 11 von 40) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch)

782481

Zoom out

Zoom in

Vorherige Seite

1/40

Nächste Seite

this dimension “X”.

2) The distance from the intermediate point between the

two rear rollers to the middle of the ARION front roller,

which we will call “Y” (Fig.3), must match or be as near

as possible to dimension “X” . The axle of the ARION front

roller must be positioned in the hole of the ARION frame

whose measurement given on the graduated scale is

closest to dimension “X” (Fig.4).

ATTENTION : Dimension “Y” must be equal to or slightly

greater than “X”. The rollers can be adjusted to adapt them

to bicycles whose wheelbase is 0944-1124 mm (37 to 44

inches).

3) To change Y it is necessary to shift the front roller D .

4) Fold the ARION until the drive belt E slackens.

5) Loosen the drive belt E , making it come off the

respective front and rear guides.

6) Unfold the ARION back into the open position.

7) Remove the rectangular covers B (using a screwdriver

if necessary), and the screws and washers on both sides

from the front roller, using the Allen key F provided. (Fig.

5a - 5b)

8) Pull the roller out from its original position.

9) Position the roller in the appropriate seat in the holes in

the frame, so that X matches Y.

10) Refit the screws and the washers in the special holes,

but do not tighten them down.

11) Close the ARION, position the drive belt E on the guide

of the front roller D and middle roller.

12) Unfold the ARION into open position again.

13) Check the position of the front roller D , putting your

bicycle on the rollers and checking that the axle for the

front wheel sits directly above the front roller.

14) Once the front roller D is positioned, tighten the screws

(do not over-tighten as this could warp the side members

A ).

15) Close the sides with the rectangular covers B . The

ARION is now ready to use.

08_ADVICE ON USING YOUR ARION

1) For carrying, or to save space when not using the roller,

it is advisable close the frame. Pay attention to the position

of hands when closing the roller, to avoid squashing them

between the two side members. To close the frame, place

hands at the ends of the side members (Fig.6).

Therefore avoid placing hands in such a way that can

become squashed between the side members (Fig.7).

2) To facilitate carrying, it is advisable to hold it by the

special grips located at the hinges (Fig.8).

3) The rollers work best with tyre that has a smooth tread.

If using a mountain bike, to reduce noise and increase

stability change the tyre for one with a slick tread.

4) For beginners, position the rollers in an entrance hall,

in a doorway or near a stable object, in order to have a

support while acquiring the necessary balance.

5) Make sure the ARION rests on a flat, stable surface.

6) Start pedalling and look ahead, like on the road.

Even if you would instinctively tend to look at the front

wheel, you will keep balance better and pedal “in a straight

line” if you concentrate on an object located 2.5 – 4 metres

(10-15 feet) in front of you.

7) If you start leaning or shift to the side of the drums,

correct your position with very light steering movements. If

you steer to much you will lose balance or end up over the

side of the rollers.

8) Keeping a fast and smooth pedalling style will help you

stay balanced on the rollers, thanks to the gyroscopic effect

of the wheels.

9) At first, pedalling on the rollers will give you a feeling

of instability, and moving the handlebar too abruptly or

pedalling heavily can make you lose control. The big

advantage of the rollers, compared to standard training

tools, is that the rollers teach you to reduce the movement

of the upper part of your body and maintain a steady

pedalling pace.

10) Do not use the bicycle brakes to stop. Rest a foot on

the ARION frame and allow the bicycle to come to a stop.

09_CARE AND MAINTENANCE

1) Prolonged exposure to direct sunlight can cause

deformation of the technopolymer rollers. Do not use or

keep the rollers in places where they are exposed to direct

sunlight.

2) Always clean the rollers after use. Only use a damp

cloth. Do not use solvents or harsh detergents.

3) If the ARION is not going to be used for a prolonged

period, release the drive belt, bringing it out of its seat, or

close it, otherwise the belt’s tension could cause early loss

of transmission efficiency.

4) The coupled bearings on the roller do not require

lubrication and are practically maintenance-free.

5) Periodically check the roller clamping screws, make sure

that they are still tight but not so tight as to damage the

plastic frame.

6) In case of wear or breakage of the drive belt, replace it

by proceeding as follows:

- remove the rectangular covers B ;

- undo the fixing screw located in the side member of the

front roller A , on one side;

- undo the fixing screw located in the side member of the

middle roller A on the same side as the previous one;

- replace the belt, refit the rollers in their correct seats and

secure all the screws again;

- close the two sides with the rectangular covers B .

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Elite Arion Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info