Bedienungsanleitung Elite Drivo (Seite 43 von 127) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch)

782410

Zoom out

Zoom in

Vorherige Seite

1/127

Nächste Seite

in use: push the safety lever (Pic. 24) and fold the front leg

(Pic. 25).

- It’s also possible to rotate the front foot by 90° (Pic. 26)

to fold the hometrainer more compactly after training. In

this case, the hometrainer must be stored horizontally as

indicated (Pic. 27) to prevent it falling and becoming da-

maged.

NOTE: For more stability place the feet (H) in the 28 ROAD

position as in (Pic. 28).

- Drivo can be stored vertically by leaning on the floor as

indicated (Pic.29), but make sure the front leaning area in

contact with the floor is rotated as indicated (Pic. 30). Be

aware that the flywheel of the hometrainer is moved up hi-

gher in this position, so any external bumps or oscillations

might cause it to fall down. The folded up hometrainer

must always be placed close to a wall that might break its

fall.

NOTE: Before storing the hometrainer in this manner,

make sure it’s safely folded up by moving its upper handle.

RECOMMENDATIONS FOR USE

Choose a cassette range that is compatible with your goals

and fitness level:

1) cassettes with a range of 11 to 23/25 teeth are recom-

mended for professional athletes and amateurs who are

able to develop high power output.

2) Cassettes with a greater number of teeth, such as 12/

13 to 27 /29, are recommended for all other cyclists.

- Derailleurs should work properly after bicycle installation

on Drivo. Occasionally, an adjustment may be necessary

for proper operation. If you have any questions, please

contact your dealer to ensure proper derailleur operation

with Drivo.

INSTRUCTIONS ON HOW TO INSTALL THE

FREEHUB WITH CAMPAGNOLO® 9/10/11

SPEED SPROCKET CASSETTES

- To replace the original freehub body installed on Drivo

with the accessory body compatible with Campagnolo®

9/10/11 speed cassettes, follow the procedure below:

1) Unscrew the adapter on the cogset shaft (Pic. 31).

2) Remove the freehub body from the Drivo shaft (Pic. 32).

3) Fully insert the Campagnolo® cassette compatible

freehub body (Pic. 33-34).

4) Tighten the cog set shaft adapter using a 5 mm hex

wrench to a torque of 5 Nm (44in-lbs). Use a medium-

strength oil tolerant threadlocker to lock the adapter on

the shaft.

- You can now mount your Campagnolo® 9/10/11 speed

cassette onto the freehub body without using the spacers

(Ref. E) (Pic. 35) (only for 11 speeds).

ATTENTION!

Strictly follow the instructions provided by the cassette ma-

nufacturer with regard to specific installation techniques,

the need for additional spacers and torque specifications.

NOTE: Please contact your dealer if you have questions

about installation or if you cannot install the cassette. The

warranty does not cover any DAMAGE to the bicycle and/

or Drivo in the event of incorrect installation.

MAINTENANCE

Drivo does not require any specific scheduled maintenan-

ce, however the following precautions are recommended:

- wipe the trainer clean with a cloth after each training

session to prevent the accumulation of dust and sweat;

- Do not clean or degrease the bicycle chain while the bike

is mounted on Drivo as solvents can cause irreparable da-

mage to the bearings or other internal mechanical parts;

- Check that the quick release is properly secured and fully

working before every training session.

WARNING: The tension of the internal transmission belt is

tested on every product by Elite’s assembly department;

do not alter belt tension as the power sensor must be re-

calibrated with every variation in belt tension.

- The belt tension may lessen after multiple uses or after

particularly intensive training sessions, and as a conse-

quence, the accuracy of the transmission of the user po-

wer output may reduced. If that’s the case, you might need

to increase the transmission belt tension by the following

method:

1) Remove the motherboard cover (Pic. 36).

2) loosen the adjustment locking screw by one full turn, so

that you can then turn the adjusting nut (Pic. 37).

3) Turn the adjusting nut half a turn to tighten the belt

correctly (Pic. 38).

4) Begin the calibration procedure as indicated in para-

graph 37.

5) Repeat the previous operation if data transmission still

not correct.

6) Once calibration is done replace the motherboard cover

(Pic. 39).

WARNING!: Make sure the re-tensioning procedure has

been pre-approved by Elite’s tech assistance department

before re-tensioning the belt (Pic. 40). Breaking the anti-

tampering seal invalidates the product’s warranty.

WARNING

- Drivo becomes hot during use. Wait for it to cool before

touching the resistance unit covers.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Elite Drivo Seite 43

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info