Bedienungsanleitung Elite Fuoripista (Seite 27 von 94) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch)

782484

Zoom out

Zoom in

Vorherige Seite

1/94

Nächste Seite

decrease its life and capacity if it's left discharged for more

than 180 days.

26_SERVICE FUNCTIONS

The two levers (Ref. L and R) can also manage service

functions.

Zero offset power meter: the power meter Zero offset

procedure can also be conducted in stand-alone mode

without the use of software or apps.

This is the procedure:

- Turn on FUORIPISTA Bike

- Take your feet off the pedals and make sure that the

flywheel is stationary.

- Maintain one of the two levers pressed forward or

backwards for 10 seconds, then the "Offset procedure not

pedalling" (Pic. 27) will be displayed on screen and the

power meter Zero procedure will begin.

- wait for it to finish. The "Offset" text with a number

(2410 is purely indicative - Pic. 28) will display when the

procedure has successfully completed.

If not, the "Fail" text will display. In this case please try the

procedure again.

Felt pad replacement: you must replace the felt pad when

it's too worn out.

Procedure:

- turn on FUORIPISTA Bike and within 10 seconds push

both lever downwards for at least 20 seconds. The

BRAKE text will display on screen, this confirms that the

FUORIPISTA Bike has entered the felt replacement mode;

- wait for FUORIPISTA Bike to fully stop to make it easier

to remove the pad.

Then FUORIPISTA Bike will enter the energy saving mode.

Replace the felt (please check out paragraph 24_BRAKE

PAD REPLACEMENT).

Brake calibration procedure

- turn on FUORIPISTA Bike and within 10 seconds keep the

emergency button pressed for at least 20 seconds. On the

display you'll see the RPM set to maintain and the actual

cyclist RPM;

- in this phase you need to pedal maintaining the on-screen

cadence (indicated in pedaling per minute) as accurately

as possible. The pedaling cadence to maintain is indicated

on screen (SET) along with the actual user cadence (RPM)

(Pic. 25);

- maintain the pedaling cadence until the calibration result

appears on screen.

FUORIPISTA Bike automatically reminds you to conduct

the procedure every 1500 km. In this case the "Calibration

needed" text will be displayed. After a few seconds this

text will disappear and the FUORIPISTA Bike can be used

as always.

Though the icon will remain on screen until the user

conducts the procedure.

27_MAINTENANCE

Clean FUORIPISTA Bike after every use to avoid wear over

time.

To clean the wooden parts (body and feet) use a product

specific to clean wooden surfaces or just use a slightly

damp cloth. Dry out everything after use.

To clean the glass parts (legs and flywheel) use a damp

cloth and dry out after. Use paper and alcohol should you

encounter tough to remove stains.

Use a slightly damp cloth to clean the metal parts, make

sure to dry them out after.

Follow the saddle manual instructions to clean the saddle.

Use a damp cloth to clean the handlebar tape from the

bottom up.

28_PACKAGING

If the roller needs to be shipped, careful packaging is critical:

- remove the charger cable from FUORIPISTA Bike;

- pack up FUORIPISTA Bike in its original box.

During shipments, packs often undergo mistreatment and

very hard impacts, therefore inadequate packing can result in

permanent damage to the roller. This type of damage is not

covered by the warranty.

Note: before sending the roller or any other component

assistance, always ﬁrstly consult Elite or the distributor.

Any items received without prior agreement will be rejected.

29_COPYRIGHT

No part of this manual may be reproduced or transmitted

without the written authorization of Elite S.r.l.

The Elite FUORIPISTA Bike software and relative code are

property of Elite S.r.l.

International copyright law protects the software.

The Elite FUORIPISTA Bike software must be treated like any

other copyrighted material, such as books.

Users undertake not to modify or adapt the programme. Users

also undertake not to decompile, disassemble or attempt in

any way to discover the native software code.

30_PRODUCT MODIFICATIONS

Also in view of any technical update, ELITE reserves the right to

make changes to the products or their speciﬁcations without

being obliged to notify or inform the Customer beforehand for:

a) changes that do not affect negatively the product

performance;

b) changes required to meet or improve the product

speciﬁcations;

c) changes necessary for the products to comply with the

applicable legal requirements.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Elite Fuoripista Seite 27

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info