Bedienungsanleitung Elite PRO-60X5FD (Seite 70 von 96) (Englisch)

534688

Zoom out

Zoom in

Vorherige Seite

1/96

Nächste Seite

• The TV can be controlled from a PC, control panels

and other devices using the RS-232C or IP.

• Use a cross-type RS-232C cable, ETHERNET cable

(commercially available) or wireless LAN for the

connections.

• This operation system should be used by a person who is

accustomed to using computers.

■

Communication conditions for IP

Connect to the TV with the following settings made for

IP on the PC.

IP protocol: TCP/IP

Host IP address: Set the IP address on the TV menu

Service: None (Do not select Telnet or SSH)

TCP port#: Set a port number on the TV menu

(Control port)

When you set your ID and password on the TV menu,

you need to enter them as soon as you connect to the

TV.

• The connection will be cut off when there has been no

communication for 3 minutes.

IP Control Setup

Example

EZ Setup

Broadcasting Setup

Internet Setup

[English]

Language

DivX

Setup

Initial Setup

I NITIAL

S ETUP

Press MENU to display the MENU screen, and then

press

to select "Initial Setup".

Press

to select "Internet Setup", and then

press ENTER.

Press

to select "Network Setup", and then

press ENTER.

Press

to select "IP Control Setup", and then

press ENTER.

Press

to select "Change", and then press

ENTER.

To use IP Control, press

to select "Enable",

and then press ENTER.

Set the device name.

Set your login ID and password.

Set the port to use with IP Control.

Conﬁ rm the settings, and then press "OK".

■

Communication conditions for RS-232C

Set the RS-232C communication settings on the PC to

match the TV's communication conditions.

The TV's communication settings are as follows:

Baud rate: 9,600 bps

Data length: 8 bits

Parity bit: None

Stop bit: 1 bit

Flow control: None

■

Communication procedure

Send the control commands from the PC via the RS-

232C or IP.

The TV operates according to the received command

and sends a response message to the PC.

Do not send multiple commands at the same time.

Wait until the PC receives the OK response before

sending the next command.

■

Command format

Eight ASCII codes

Command 4-digits

Parameter 4-digits

Return code

C1 C2 C3 C4 P1 P2 P3 P4

Command 4-digits: Command. The text of four characters.

Parameter 4-digits: Parameter 0–9, x, blank, ?

■

Parameter

Input the parameter values, aligning left, and ﬁ ll with

blank(s) for the remainder. (Be sure that 4 values are

input for the parameter.)

When the input parameter is not within an adjustable

range, "ERR" returns. (Refer to "Response code format".)

Any numerical value can replace the "x" on the table.

a 30

0009

????

When "?" is input for some

commands, the

present setting

value responds.

■

Response code format

Normal response

Return code (0DH)

Problem response (communication

error or incorrect command)

ERR

Control of the TV

Using a PC

PRO-70_60X5FD_E.indb 68PRO-70_60X5FD_E.indb 68 2011/07/01 16:38:372011/07/01 16:38:37

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Elite PRO-60X5FD Seite 70

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info