Bedienungsanleitung Elite Qubo frame (Seite 10 von 28) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch)

782390

Zoom out

Zoom in

Vorherige Seite

1/28

Nächste Seite

Thank you for choosing the Qubo

INTRODUCTION

Check the presence of all the following components:

N°1 Qubo frame (Ref. A)

N°1 Unit (Ref. B)

N°1 Quick release (Ref. C)

N°2 M6 Unit screws (Ref. D)

N°10 Levelling (equalizing) feet (Ref. E)

ATTENTION

Resistance unit depicted here may vary from

production models

UNIT ASSEMBLY

• Unfold the frame (A) from its packaged position (Pic. 1)

and place it on a flat surface (Pic. 2)

• There are 2 pairs of holes on its base to be used with

different roller diameter options:

1) Use the front pair of holes for a 30mm diameter roller

unit (Pic. 3);

2) Use the rear pair of holes for a 45mm diameter roller

unit (Pic. 4);

• Tighten the M6 screws (D) (Pic. 5 and Pic. 6) completely,

utilizing the correct holes for the different roller diameter

options.

• Use solely the included wrench to attach the resistance

unit to the frame base as shown in the figure. Tighten ¼ of

a turn after contact is made between resistance unit and

frame base (apply max force 2 Nm) (Pic. 7).

FITTING THE BICYCLE

• Make sure the quick release of the bicycle rear wheel is

properly fixed.

• Turn the lever (F) to the “open” position (Pic. 8).

• Put the bicycle in position, inserting the left end of the

rear quick release in the left bushing (Pic. 9). For safer

clamping of the bicycle on the stand, make sure the lever

of the quick release is horizontal (Pic. 10).

• Close the lever (F), making sure it starts pressing the

quick release inside the predefined work

area; between 55° and 65° (Pic. 11).

• If the lever (F) starts pressing the quick release in the

advanced work position (Pic. 12), screw the

left bushing pin (g) (Pic. 13) so that the lever (F) starts

working inside the predefined work area (between 55° and

65°) (Pic. 11).

• If the lever (F) starts pressing the quick release in the

delayed work position (Pic. 14), unscrew the left bushing

pin (G) (Pic. 15) so that the lever starts working inside the

predefined work area (between 55° and 65°) (Pic. 11).

• If the bicycle wheel sets up too far from the centre of the

roller (Pic. 16), loosen the resistance unit (B) attachment

bolts (D), slide the resistance unit left or right as necessary,

and re-tighten the bolts (Pic.17, Pic.18 and Pic.19).

• Push the bicycle towards the resistance unit until the rear

wheel touches the roller (Pic. 20).

• Verify the stability of the bike by pushing and pulling the

horizontal tube of the frame and the saddle. Should the

bike still not appear stable, make sure its quick release and

lever are correctly positioned, that the lever (F) is in a

“closed” position and the adjusting of the clamping system

has been carried out correctly.

BIKE REMOVAL

• Hold the bicycle with one hand and with the other open

the lever (F), turning it to the “open” position (Pic. 21).

Remove the bicycle.

• For carrying, or storage, it is advisable to close the stand.

(Pic.22 e Pic.23).

• In order to further reduce the storage footprint remove

the unit (B) from the frame (A) and place it back in its ori-

ginal packaging and fold the frame as indicated in Pic. 24

and Pic. 25.

LEVELLING FEET ASSEMBLY

• The Qubo frame (A) comes equipped with levelling feet

(E) to compensate for uneven surfaces that do not allow the

four feet to make complete contact, and to allow the bike

to be perfectly vertical (Pic. 26).

• The levelling feet (E) can be mounted under the front feet

(Pic. 267 and Pic. 28).

• The levelling feet (E) can be mounted under the rear feet

(Pic. 29 and Pic. 30).

• If a single levelling foot (E) isn’t sufficient, it is possible

to add additional feet to those already mounted. (Pic. 31,

Pic. 32, Pic. 33 and Pic. 34).

Warning: the direction of the foot (E) is turned 90° in rela-

tion to the first one positioned.

ATTENTION

• Keep people, children and animals away from the roller

during use, since the moving and rota- ting parts of the

roller and the bicycle can cause damage in case of contact.

• Before you start training, place the trainer in a suitable

location, away from any potentially dangerous objects

(furniture, tables, chairs...) so as to avoid any risk of acci-

dental or inadvertent contact.

• The stand is designed for use by just one cyclist. • Check

the safety and stability of the bicycle before every training

session.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Elite Qubo frame Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info