Bedienungsanleitung Elkron DT600 (Seite 8 von 24) (Deutsch, Englisch, Französisch, Italienisch)

741399

Zoom out

Zoom in

Vorherige Seite

1/24

Nächste Seite

8 DS80IM41-001B

Sensitivity Function (Increase of Sensitivity)

NORMAL: Dip Switch N°1 in OFF position (Default). Recommended for most exterior installations.

HIGH: Dip Switch N°1 in ON position. Recommended when a higher detection speed is required.

Trimmer (sensor capacity)

This regulates the sensor capacity (turning the trimmer clockwise increases the detector capacity). To adjust it, keep in mind the

operating area determined by the microwave. The sensor will automatically adapt the functioning of the infra-red with this

regulation. The trimmer default position is completely clockwise turned.

<NOTE>

Unlike the microwave, for which it is possible to establish its detector limit with sufficient precision, this condition is not

applicable for the infra-red. The reason is because the detection of the infra-red is conditioned by the ambient temperature,

by the intruder’s clothing, by the absence/presence of wind, etc. The trimmer therefore automatically regulates the infra-red

detection capacity in function of the capacity of the microwave selected without necessarily defining its operating area as that

of the microwave itself (the infra-red will be configured for the most unfavourable conditions at that capacity).

Detector LED indicator

Dip Switch N° 3 in OFF position

In the normal operating mode, the LED indicator blinks to indicate the transmission of the signal in the following situations:



When it is powered, it blinks for 60 seconds (initialisation phase).



When the cover is open and the tamper switch is activated, for 4 minutes (test mode).



During the test mode for every movement detected



If the tamper is open, for every movement detected.

It does not blink if a movement is detected in normal mode and with the tamper closed.

Dip Switch N°3 in ON position (Default)

The LED also blinks when a movement is detected in normal operating mode and with the tamper closed, at the cost of depleting

the battery. It is inhibited as soon as the cut-off time starts.

Battery

The detector is powered by a CR2 3V lithium battery provided in the package. The detector is capable of detecting the flat

battery status, sending a signal to the control unit together with the normal transmission of signals so that the control unit

displays the corresponding status.

<NOTE>



During the replacement of the battery, after having removed the dead battery, press the tamper twice to completely

discharge the device before inserting the new battery.



To check that it is functioning correctly, conduct the Walk Test for the radio signal level capacity by pressing the

learning button, button 11 (see the control unit instruction manual).

Detector learning

To open the sensor, lift the LED filter screw covers and loosen the closure

screws beneath it. Loosen the screws that hold the card in place without

unscrewing them completely and disassemble the electronic card, lifting it

upward first to release it from the screw, as illustrated here.

 Insert the CR2 battery into the battery compartment, taking care to

observe the polarity.

 When the detector LED indicator is powered, it blinks for 60 seconds

(initialisation phase). The detector is not yet activated.

 Enable the control unit for the learning device. For details, see the

control unit instruction manual.

 Press the learning button on the radio circuit and complete the learning

process (see the control unit instruction manual).

 Put the control unit in “Radio Device Test” mode after the detector

learning procedure.

 Insert the circuit on the bottom, tighten the screws and close the front

panel, positioning the detector in the where it is to be installed.

 Once the radio cover is checked, it is possible to reopen the front panel, disassemble the circuit and attach the detector

directly onto the wall or using the bracket and optional articulation.

 Tighten the closure screws.

 Apply the LED filter screw covers.

Installation on flat surfaces



The detector was designed to be assembled on a flat surface, using the fastening screws and the anchor bolts provided.



The base is marked where the plastic is thinner for boring holes suitable for installation.

I. Cut seat A and seat B on the bottom (see the image below).

II. Using the holes template, make holes on the surface.

Card screw

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Elkron DT600 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Elkron DT600

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info