Bedienungsanleitung Elkron EIR600FC (Seite 5 von 12) (Deutsch, Englisch, Französisch, Italienisch)

741427

Zoom out

Zoom in

Vorherige Seite

1/12

Nächste Seite



Learning of the detector by the control unit

The detector must be learnt by the control unit to transmit the signal if motion is detected. Proceed as follows to perform the

device learning procedure.

The detector may be learnt by the control unit only within three minutes from switch-on.

1. Remove the sun visor fastening screws to remove this component.

2. Remove the battery compartment cover to open the battery compartment and the dip switches.

3. If necessary, configure the dip switches; for information on setting, see the table provided above.

4. Insert the two lithium batteries “AA” L91 in the battery compartment, taking care to observe the polarity.

5. Make sure that the Tamper switch is open (released) before proceeding to the next step.

6. Within three minutes from switch-on, hold the function button pressed for 10 seconds and then release it when the red

LED and the illuminator blink once. Make sure that the learn function has been activated on the control unit.

7. After having been leant by the control unit, the detector is automatically recorded in the system. Check the control unit

to check that the learning and registration procedure were performed correctly.

8. Once learnt by the control unit, if the detector connection is lost, the LED will blink for 20 minutes to signal the fault.



Test mode

The Test mode is used to control the detection coverage of the device not the communication range with the control unit.

To access test mode, hold the function button pressed for a few seconds then release it to start the test mode that lasts for three

minutes.

The detector will start initialisation during the first 30 seconds. It is advisable not to generate alarms during this time.

Motion detection in front of the detector can be checked at the end of the initialisation period. The red LED lights up for two

seconds after detection.



Mounting and installation method

The detector was designed to be mounted on a flat surface or in a corner by means of the fixing screws and the anchor bolts

provided.



The package contains a metal rotation bracket to allow adjusting the camera and sensor angle. The bracket is

provided with holes for fixing to a wall or in a corner.

1. Use the installation holes on the rotation bracket to mark the corresponding points on the wall or in a corner; if

necessary, insert the anchor bolts into the wall.

2. Screw the rotation bracket in the marked installation points.

3. Screw the bracket arm onto the detector (Figure 1).

4. Clip on the detector onto the rotation bracket and adjust the detector angle with the upper holes of the bracket

(Figure 2).

5. Fix the detector onto the bracket by tightening the upper screw (Figure 3).

Figure 1 Figure 2 Figure 3

Camera

installation

Corner installation

holes

Camera angle selection

Corner installation holes

Installation

holes in wall

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Elkron EIR600FC Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Elkron EIR600FC

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info