Bedienungsanleitung Elkron IM600 (Seite 6 von 16) (Deutsch, Englisch, Französisch, Italienisch)

741436

Zoom out

Zoom in

Vorherige Seite

1/16

Nächste Seite

6 DS80IM39-001B

Use Test mode to determine the detection coverage of the detector during sensor installation.

 Microwave Test mode

The microwave test mode is used to test the microwave range only. Use the jumper JP3 to enable microwave test mode.

When the detector is in microwave test mode, PIR detection is deactivated, the microwave transmitter is activated to repeatedly

send microwave signals for detecting motion. When the detector detects motion in microwave Test mode, the blue microwave

LED generates a signal by lighting up for a short time.

Use microwave Test mode to determine the microwave range and adjust the range using the microwave range switch, if

needed. Make sure that microwave test mode is off after having completed the test, setting Jumper JP3 to OFF and returning

the detector to normal operation.

 Battery

 The detector is powered by a CR123A lithium battery.

 The detector is provided with flat battery detection function; when a flat battery is detected, a flat battery signal is sent

to the control unit with the normal signal transmission (e.g. with supervision signal).

 If the battery is not replaced after flat battery conditions have been detected and the battery is entirely discharged, the

detector will stop working all together. The red LED will blink every 4 seconds.

 While replacing the batteries, after having removed the flat batteries, press the tamper or learning/test button a few

times to discharge the device completely before inserting the new batteries.

 Supervision

The detector transmits a supervision signal at constant intervals.

If the control unit cannot receive the supervision signals transmitted by the detector for a pre-set period of time, it indicates a

Supervision alarm.

 Tamper switch

The detector is protected by a tamper switch which exits from the hole provided in the rear cover and is normally compressed

against a wall or an installation surface. The tamper alarm is activated when the detector is removed form the installation

surface.

 Pre-cut areas

The rear cover of the detector has two pre-cut areas. When the device is installed correctly, if an intruder forces the

detector from the position in which it is mounted, the areas are detected from the rear cover and remain attached to the

mounting surface while the main body of the device is removed, activating the tamper switch.

Learning and installation

 Preparation

1. Orient and insert the battery according to the polarity.

2. The red LED will start blinking for 30 seconds to indicate that the detector is being initialised. During initialisation, the

detector will not be activated. It is advisable to move away from the detection area during this time. At the end of the

initialisation time, the red light goes off and the detector passes to normal operation.

3. Set the control unit to learning mode; see the instruction manual of the control unit for details.

4. Press the Learn/Test button to transmit the signal to the control unit

5. The corresponding information of the device is displayed if the control unit receives the signal. Refer to the manual of the

control unit to complete the learning process.

6. Put the control unit in Walk Test mode (motion Test) after the detector learning procedure. Hold the detector in the required

position, press the Test button to check that the concerned position is within the communication coverage range.

7. Proceed with the installation after having ascertained that chosen position is satisfactory.

 Mounting method

 The detector was designed to be mounted on a flat surface or in a corner using the fixing screws and the anchor bolts

provided.

 The rear base is provided with a hole arrangement when the plastic is thinner to allow mounting. There are two hole

arrangements on the back for fixing on surface, while there are four on the sides of fixing to a corner.

 Surface mounting

I. Separate the base and the cover.

II. Perforate the appropriate hole arrangements on

the inner side of the base.

III. Using a template for the holes, make the holes in

the surface.

IV. Insert the anchor bolts if the device is fixed to

plaster or bricks.

V. Screw the base into the anchor bolts.

VI. Arrange the base on the cover.

 Corner mounting:

I. Perforate the fixing hole arrangements on the

triangular bracket provided.

II. Using a template for the holes, make the holes in

the corner.

Arrangements for

central holes for

mounting on flat

surface

Arrangements

for mounting the

corner bracket

Hole arrangements

for fixing bracket

Triangular bracket

for corner

installation

Recess for

tamper

com

ression

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Elkron IM600 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info