Bedienungsanleitung Elkron MP110M (Seite 4 von 20) (Englisch)

741486

Zoom out

Zoom in

Vorherige Seite

1/20

Nächste Seite

(((ELKRON)))

MP110 USER MANUAL

(((ELKRON)))

MP110 USER MANUAL

4. To disarm the system, insert the key and remove it when the leds go

OFF.

Recognition of Key with Masked System

• When the system is masked, all the commutator leds are OFF.In this

way it is impossible to know whether the system is armed and masked

or actually turned OFF.

• The insertion of a key with valid code causes all four commutator leds

to light up for 0.5s. This indicates that the key code has been correctly

readand is followed by the display of system mode for 3.5 seconds.

• Removal of the key before this time has expired causes the system to

return to the masked mode; leaving the key inserted enables a change

in system mode like the one that took place with the arming/disarming

procedure by electronic key.

• While the commutators always mask system mode, the keypads only

perform masking if the unit is armed. When OFF, all data is visible as

if the system were unmasked.

Code Recognition with Masked System

• With masked system, all keypad leds are off, except for the mains led.

In this way it is not possible to know whether the system is armed and

masked or it is really off.

• By entering a valid code the keypad being used visualizes the plant

status for one minute: within this period it is possible to operate.

• After 1 minute from the introduction of the code, the system is masked

again.

2.Access Codes

• The unit can be programmed so as to enable User 2 (e.g., service

personnel, custodian, porter , telemonitoring, private vigilance, etc)

to have his own secret access code which allows him to arm/disarm

the unit without performing other operations.

• The unit identifies up to a maximum of 8 different assigned codes and

as many users:

• After entering a correct code that is enabled, the unit’s buzzer beeps

twice, or it beeps once at length to indicate an error. The Master user’s

code is always enabled; the other codes must instead be enabled (refer

to par. “Code Enabling”).

• If the engineer’s code is enabled, it remains enabled until the Master

user’s code is again entered to partially or totally arm the system, or

until the first arming by electronic key-

• Once armed, every re-entry/EXCLUDED display procedure triggers a

1-minute delay (that is reset each time the key is pressed). If a delay

time-out occurs, the procedure is exited automatically without saving

the changes made.

• The pressing of each key whileentering the secret code causes an

asterisk to be displayed.

FACTORY

CODE

CODE 1 - MASTER USER 1 11111

CODE 2 - USER 2 2 22222

CODE 3 - ENGINEER 3 33333

CODE 4 - TELEMONITORING 4 44444

CODE 5 - USER 5 5 55555

CODE 6 - USER 6 6 66666

CODE 7 - USER 7 7 77777

CODE 8 - USER 8 8 88888

Each user is assigned and “identification

number “ (from 1 to 8) that is to be typed in

before the code; this number allows the unit to

identify the user of the system. To be identified

by the system, the owner must type in the

number 1 followed by his personal code; any

other users will instead type in the number 2,

3, 4, 5, 6, 7 or 8, followed by his personal code

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Elkron MP110M Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Elkron MP110M

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info