Bedienungsanleitung Elkron MP110MTG (Seite 17 von 20) (Englisch)

741487

Zoom out

Zoom in

Vorherige Seite

1/20

Nächste Seite

(((ELKRON)))

MP110 USER MANUAL

(((ELKRON)))

MP110 USER MANUAL

14. List of Messages on Display

MESSAGE: NOTES:

‘No PWR C.U. ZONES’ Short circuit or no power to inputs.

‘No PWR OUTPUTS‘ Short circuit or no power to sirens.

‘No PWR SERIAL ‘ Short circuit or no serial power to peripherals.

‘LOW BATTERY’ Low,exhausted, no battery.

‘NO MAIN CONTROL PANEL’ No mains in control unit.

‘C.U. PWR SUPPLY’ Low power to control unit sensors.

(ccc)=Codice di accesso usato per operare (ove compare).

‘No PWR C.U. ZONES’ Input power failure.

‘No PWR OUTPUTS ‘ Siren power failure.

‘No PWR SERIAL ‘ Serial peripheral power failure.

“OK BATTERY ‘ Recharged battery.

‘OK MAIN’ Mains return to control unit.

‘—On/Off— unn’ Status shift (On/Off).

‘ON FROM REMOTE ‘ Remote arming (via FASTLINK).

‘START TEST unn’ Plant test start.

‘END TEST unn’ Plant test end.

‘START TELEG. unn” Telemanagement start (FASTLINK).

‘END TELEG. unn’ Telemanagement end (FASTLINK).

‘ALARM ZONE xx’ Alarm message –zone xx.

‘TAMPER ZONE xx’ Tamper message – zone xx ( For double bil inputs).

‘Z24 CONTROL PAN’ Control unit self-protection.

‘FALSE USER CODE’ Alarm due to false code entered from keypad.

‘FALSE KEY CODE’ Alarm due to false key code.

‘TAMPER KEYPAD x’ Keypad x self-protection.

‘ BUS READER x’ Tamper of commutator x serial line.

‘ BUS KEYPAD x’ Tamper of keypad x serial line.

‘ccc INSULAT. Z.nn’ Zone xx bypassing message carried out by user ccc

‘ccc SETTED Z.xx’ Zone xx reentry message carried out by user ccc

4.Sensor EXCLUDED/Re-entry

1. Enter the Master USER code and press the

key.

2. The first sensor available for EXCLUDED is shown. The display

indicates “nn” (where nn is the number of sensor, refer to the sensor

table to know to which zone it corresponds).

3. Use the

key for forwardEXCLUDED sensor selection

Use the

key for backward EXCLUDED sensor selection

Use the

TOTAL

key to return to the beginning of list

4. To EXCLUDED the sensor under consideration, press

The sensor number will flash on the keypad screen.

If all sensors are EXCLUDED, “--” (two hyphens) will appear on the

display.

5. Press

EXIT

to exit programming.

1. Enter the Master USER code and press the

key.

2. Re-entry of the first EXCLUDED sensor will be proposed. The display

indicates “nn” (where nn is the number of the EXCLUDED sensor,

refer to the sensor table to know the zone to which it corresponds).

3. Use the

key for forward EXCLUDED sensor selection

Use the

key for backward EXCLUDED sensor selection

Use the

TOTAL

key to return to the begiinning of list

4. To re-enter the zone under consideration, press

5. The number of the sensor flashes on the keypad screen To select the

next zone, press the

key. If there are no EXCLUDED

zones, the symbol “- -” (two hyphens) appears on the display.

6. Press

EXIT

to exit programming

4.1 Sensor EXCLUDED

4.2

Re-entry of Previously EXCLUDED Sensors

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Elkron MP110MTG Seite 17

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Elkron MP110MTG

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info