Bedienungsanleitung Elkron MP110TG (Seite 15 von 20) (Englisch)

741485

Zoom out

Zoom in

Vorherige Seite

1/20

Nächste Seite

(((ELKRON)))

MP110 USER MANUAL

(((ELKRON)))

MP110 USER MANUAL

10. Call Result Visualization

1. Further to an alarm, this procedure allows to verify which telephone

numbers have been called and which of them have properly answered.

2. Enter MASTER code +

3. The following message is visualized:

“

#:nnnnnn*:nnnnnn

” where n=the corresponding telephone number.

The first group of numbers (left) identifies the called numbers, the right

group the numbers that have properly answered.

In the following example, all numbers have been called and all of them

have properly answered: #:123456*:123456.

In the following example numbers 2,4,5,6 have been called by only

numbers 2,5,and 6 have properly answered: #:-2-456*:2—56.

4. In case of information lack the displays will visualize the following

messages: #:________*:_________

5. To cancel information press key

6. To exit from procedure, press key

EXIT

twice.

11. Listening to Voice Messages

• Listening takes place by means of the loudspeaker connected to the

voice board in the control unit

1. Enter the MASTER USER access code

2. Press keys

TEL

3. Press the

key to begin to reproduce the messages recorded, the

system returns to the communicator menu after all messages have been

heard.

4. If one wishes to listen to a particular message, use the

keys to select the desired message and start reproducing with the

key

5. After messages have been played reproduced, it is possible to select

the next message. Press

EXIT

to exit the message play back procedure

and return to the communicator menu.

- Press the

key, followed by

key .

- The display visualizes the following information in sequence approx.

every 1 second:

• flashing: ‘hours’ from 00 to 12.

• flashing: ‘minutes’ from 00 a 59.

• exits from procedure.

5.4 Time Visualization

5.6 Display of EXCLUDED Sensors

• One or more open zones are indicated by the flashing of the

led. To display these, press the

key.

• The number “nn” is displayed (where nn is the number of the sensor,

refer to the sensor table to know to which zone it correspsonds)

5.3 Display of Open Zones

• One or more EXCLUDED sensors are indicated by the flashing of the

led.

• To display the EXCLUDED sensors, type in the USER 1 code and press

the

key.

• The first EXCLUDED zone is displayed with “nn” (where nn is the number

of the sensor, refer to the sensor table to know to which zone it

corresponds)

- Press the

key, followed by

key .

- The display visualizes the following information in sequence approx.

every 1 second:

• nn flashing, where nn = day of the month.

• nn where nn = month from 1 to 12.

• nn flashing, where nn = year from 00 to 99 (00=2000,

01=2001, etc.)

• exits from procedure.

5.5 Date Visualization

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Elkron MP110TG Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Elkron MP110TG

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info