Bedienungsanleitung Elm 327 (Seite 10 von 94) (Englisch)

612699

Zoom out

Zoom in

Vorherige Seite

1/94

Nächste Seite

Several parameters within the ELM327 can be

adjusted in order to modify its behaviour. These do not

normally have to be changed before attempting to talk

to the vehicle, but occasionally the user may wish to

customize these settings – for example by turning the

character echo off, adjusting a timeout value, or

changing the header bytes. In order to do this, internal

‘AT’ commands must be used.

Those familiar with PC modems will immediately

recognize AT commands as a standard way in which

modems are internally configured. The ELM327 uses

essentially the same method, always watching the

data sent by the PC, looking for messages that begin

with the character ‘A’ followed by the character ‘T’. If

found, the next characters will be interpreted as an

internal configuration or ‘AT’ command, and will be

executed upon receipt of a terminating carriage return

character. If the command is just a setting change, the

ELM327 will reply with the characters ‘OK’, to say that

it was successfully completed.

Some of the following commands allow passing

numbers as arguments in order to set the internal

values. These will always be hexadecimal numbers

which must generally be provided in pairs. The

hexadecimal conversion chart in the OBD Commands

section (page 30) may be helpful if you wish to

interpret the values. Also, you should be aware that for

the on/off types of commands, the second character is

the number 1 or the number 0, the universal terms for

on and off.

The remainder of this page, and the two pages

following provide a summary of all of the commands

that the current version of the ELM327 recognizes. A

more complete description of each command begins

on page 12. Note that the settings which are shown

with an asterisk (*) are the default values.

10 of 94

ELM327

ELM327DSJ Elm Electronics – Circuits for the Hobbyist

www.elmelectronics.com

AT Command Summary

AT Commands

General Commands

<CR> repeat the last command

BRD hh try Baud Rate Divisor hh

BRT hh set Baud Rate Timeout

D set all to Defaults

E0, E1 Echo off, or on*

FE Forget Events

I print the version ID

L0, L1 Linefeeds off, or on

LP go to Low Power mode

M0, M1 Memory off, or on

RD Read the stored Data

SD hh Save Data byte hh

WS Warm Start (quick software reset)

Z reset all

@1 display the device description

@2 display the device identifier

@3 cccccccccccc store the @2 identifier

Programmable Parameter Commands

PP xx OFF disable Prog Parameter xx

PP FF OFF all Prog Parameters disabled

PP xx ON enable Prog Parameter xx

PP FF ON all Prog Parameters enabled

PP xx SV yy for PP xx, Set the Value to yy

PPS print a PP Summary

Voltage Reading Commands

CV dddd Calibrate the Voltage to dd.dd volts

CV 0000 restore CV value to factory setting

RV Read the input Voltage

Other

IGN read the IgnMon input level

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Elm 327 Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info