Bedienungsanleitung Elm 327 (Seite 23 von 94) (Englisch)

612699

Zoom out

Zoom in

Vorherige Seite

1/94

Nächste Seite

23 of 94

ELM327

ELM327DSJ Elm Electronics – Circuits for the Hobbyist

www.elmelectronics.com

AT Command Descriptions (continued)

Values passed in this way do not affect those that

are stored in the 2C and 2D Programmable

Parameters, and are lost if the ELM327 is reset. If you

want to make your settings persist over power cycles,

then you may wish to store them in the Programmable

Parameter for CAN protocols USER1 or USER2.

PC [ Protocol Close ]

There may be occasions where it is desirable to

stop (deactivate) a protocol. Perhaps you are not using

the automatic protocol finding, and wish to manually

activate and deactivate protocols. Perhaps you wish to

stop the sending of idle (wakeup) messages, or have

another reason. The PC command is used in these

cases to force a protocol to close.

PP hh OFF [ turn Prog. Parameter hh OFF ]

This command disables Programmable Parameter

number hh. Any value assigned using the PP hh SV

command will no longer be used, and the factory

default setting will once again be in effect. The actual

time when the new value for this parameter becomes

effective is determined by its type. Refer to the

Programmable Parameters section (page 69) for more

information on the types.

Note that ‘PP FF OFF’ is a special command that

disables all of the Programmable Parameters, as if you

had entered PP OFF for every possible one.

It is possible to alter some of the Programmable

Parameters so that it may be difficult, or even

impossible, to communicate with the ELM327. If this

occurs, there is a hardware means of resetting all of

the Programmable Parameters at once. Connect a

jumper from circuit common to pin 28, holding it there

while powering up the ELM327 circuit. Hold it in

position until you see the RS232 Receive LED begin to

flash (which indicates that all of the PPs have been

turned off). At this point, remove the jumper to allow

the IC to perform a normal startup. Note that a reset of

the PPs occurs quite quickly – if you are holding the

jumper on for more than a few seconds and do not see

the RS232 receive light flashing, remove the jumper

and try again, as there may be a problem with your

connection.

PP hh ON [ turn Programmable Parameter hh ON ]

This command enables Programmable Parameter

number hh. Once enabled, any value assigned using

the PP hh SV command will be used where the factory

default value was before. (All of the programmable

parameter values are set to their default values at the

factory, so enabling a programmable parameter before

assigning a value to it will not cause problems.) The

actual time when the value for this parameter becomes

effective is determined by its type. Refer to the

Programmable Parameters section (page 69) for more

information on the types.

Note that ‘PP FF ON’ is a special command that

enables all of the Programmable Parameters at the

same time.

PP hh SV yy [ Prog. Param. hh: Set the Value to yy ]

A value is assigned to a Programmable Parameter

using this command. The system will not be able to

use this new value until the Programmable Parameter

has been enabled, with PP hh ON.

PPS [ Programmable Parameter Summary ]

The complete range of current Programmable

Parameters are displayed with this command (even

those not yet implemented). Each is shown as a PP

number followed by a colon and the value that is

assigned to it. This is followed by a single digit – either

‘N’ or ‘F’ to show that it is ON (enabled), or OFF

(disabled), respectively. See the Programmable

Parameters section for a more complete discussion.

R0 and R1 [ Responses off or on ]

These commands control the ELM327’s automatic

receive (and display) of the messages returned by the

vehicle. If responses have been turned off, the IC will

not wait for a reply from the vehicle after sending a

request, and will return immediately to wait for the next

RS232 command (the ELM327 does not print anything

to say that the send was successful, but you will see a

message if it was not).

R0 may be useful to send commands blindly when

using the IC for a non-OBD network application, or

when simulating an ECU in a learning environment. It

is not recommended that this option used for normal

OBD communications, however, as the vehicle may

have difficulty if it is expecting an acknowledgement

and never receives one.

An R0 setting will always override any ‘number of

responses digit’ that is provided with an OBD request.

The default setting is R1, or responses on.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Elm 327 Seite 23

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info