Bedienungsanleitung Elro AG40KE (Seite 2 von 2) (Englisch)

708661

Zoom out

Zoom in

Vorherige Seite

1/2

Nächste Seite

INTRODUCTION

The code lock AG40KE11B is designed for use in combinaon with the Home Alarm System AG400011. By using

a 4-digit access code you can turn the alarm system armed, parally armed and disarmed. In addion, a panic

alarm can be acvated.

Transmission

Low Baery

Code Conﬁrmaon

Arm

Disarm

PARM1

PARM2

INSERTING THE BATTERY

To insert the baery, ﬁrst remove the mounng plate by unscrewing the (a) screw on the boom of the unit.

Next, unscrew the two screws of the baery plate (b) on the back of the unit. Then insert the included 9-volt

baery (c) in the compartment and screw the baery plate back on.

MOUNTING PLATE

Use the mounng plate you unscrewed in the previous step as a

template to mark the drill holes on the wall. Aer drilling the holes,

ﬁx the mounng plate to the wall with the included wall plugs and

screws. When you have completed conﬁguraon, you can place the

keypad back in the mounng plate and screw it back in with the

screw (a) on the boom.

ADDING THE WIRELESS KEYPAD TO THE HOME ALARM SYSTEM AG4000

1. On the alarm panel, enter the alarm panel’s PIN (1234 by default) + DISARM to disarm the system.

2. Enter PIN (1234 by default) + 15 + PARM to start the binding process. The DISARM LED will start to

blink for 30 seconds with a beep tone. Within 30 seconds, set the remote keypad to enter binding mode by

using the tamper switch (d) on the back.

3. If the remote keypad is added successfully, the DISARM LED will turn on for 1 second along with a long

beep sound. If the binding process fails, it will meout aer 30 seconds and 3 short beeps will be heard. To

exit the binding process, press the DISARM key on the alarm panel.

CHANGING THE ACCESS CODE

For security, it is highly recommended that you change the standard PIN (1234) to a four-digit PIN of your own

choosing. The system can support one master user code, and ﬁve user access codes.

* To set a new master access code take the following steps

1. Press followed by the standard PIN (1234) and again .

The LED will now light up and ﬂash three mes.

2. Choose a new four-digit PIN and enter this now, followed by . The LED will now light up and

ﬂash four mes to conﬁrm. The master access code has now been changed.

* To set user access codes, take the following steps

1. Press followed by the master access code you have set in the previous step and then again .

The LED will now light up and ﬂash three mes.

2. Enter (for user code 1) followed by and then the four-digit user access code you wish to set,

followed by . The LED will now light up and ﬂash four mes.

3. To set user access codes 2-5, simply repeat the above steps but replace the with a number 2-5.

Note: The user access codes will only apply to the remote keypad. When operang the home alarm system from

the main alarm panel, you will sll need to use the PIN you have set for that.

TESTING THE REMOTE KEYPAD

To fully arm the system: Enter [your access code] followed by

Parally arm the system: Enter [your access code] followed by or

To disarm the system: Enter [your access code] followed by

Your buon presses will be conﬁrmed by the lighng up. It is important you also conﬁrm the

transmission of the code once you have ﬁnished entering the command by seeing if the is ﬂashing. When

ﬁrst seng up the system, we recommend you test it near the main alarm panel so that you can conﬁrm the

keypad successfully transmied by seeing the alarm mode change on the alarm panel and hearing a beep tone.

PANIC SIGNAL

The remote keypad allows you to send a panic signal, for instance because you are using the remote keypad

under duress. To send a panic signal, press and hold the and at the same me for at least two

seconds and unl the LED is ﬂashing rapidly.

DISABLING THE REMOTE KEYPAD

If a sequence of more than 16 incorrect key presses is entered, the keypad will be disabled for 1 minute. If the

keypad is consecuvely disabled 3 mes, the keypad will send a tamper signal to the alarm panel and the

LED will ﬂash slowly.

Note: When the keypad is disabled for 1 minute, the LED will ﬂash slowly, indicang that the Keypad is

temporarily shut down. During this minute, any key presses will be treated as an invalid input. Aer 1 minute

has elapsed, correct input will be accepted again.

(a)

(b)

(c)

(a)

Tamper

switch

(d)

-1- -2-

8 9

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Elro AG40KE Seite 2

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Elro AG40KE

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info