Bedienungsanleitung Elro AG40MA (Seite 2 von 2) (Englisch)

708656

Zoom out

Zoom in

Vorherige Seite

1/2

Nächste Seite

INTRODUCTION

The door/window sensor AG40MA11 is designed for use with the Home Alarm System AG400011.

The Magnec sensor consists of two parts; a detector (a) and a magnet (b). Designed to be ﬁed to doors or

windows with the magnet mounted on the moving/opening part, and can then detect when the door or

window is opened.

INSERTING BATTERIES

Unscrew the screw (c) at the boom of the sensor to remove the rear cover (d), and place the 3 included 1.5V

AAA baeries in the baery compartment. Ensure you are not pressing the tamper switch (e) on the boom of

the sensor. Then remove or bring the magnet to the detector, the LED (f) of the detector lights up.

LINKING TO THE HOME ALARM SYSTEM AG400011

Before mounng the sensor, you must ﬁrst link the sensor to the alarm panel. When adding a sensor to the

alarm system, it can be added under ﬁve diﬀerent security types that diﬀer based on in which mode they can

give an alert and whether or not there is a delay. The types are:

- Security Type “0”: Fully Armed: The sensor will be acvated only when the system is in Full Arm mode. This

sensor will not be acvated in Paral Arm mode. When the sensor is triggered, the alarm will sound

immediately without any preset delay.

- Security Type “1”: Parally Armed and Fully Armed: The sensor will be acvated when the system is either

fully or parally armed. When the sensor is triggered the alarm will sound immediately without any preset

delay.

- Security Type “2”: Fully Armed + Delay: Same as Security Type “0”, except when the sensor is triggered the

alarm will sound aer a preset Entry delay. This is mostly used for the main entrance to prevent any

accidental triggering of the alarm by the user.

- Security Type “3”: Paral Arm and Fully Arm + Delay: Same as Security Type “1” except when the sensor is

triggered the alarm will sound aer a preset Entry delay. This is mostly used for the main entrance to

prevent any accidental triggering of the alarm by the user.

- Security Type “4”: 24Hrs intruder: The sensor will immediately trigger an alarm, regardless whether the

system is (parally) armed or disarmed. This is normally used to protect areas from any unauthorized access,

such as a safe box or an electrical maintenance room, etc.

When you have selected which security type ﬁts best with the sensor you are using, follow these steps to link

the sensor to the alarm system:

1. Ensure you have inserted the baeries so that the sensor is powered on

2. On the alarm panel, enter your PIN + DISARM key to disarm the system.

3. Then enter your PIN + 15 + (Security Type) + PARM to start the binding process.

The DISARM LED will start to blink for 30 seconds with a beep tone.

4. Within 30 seconds, set the sensor to enter binding mode by pressing the tamper key on the back for a few

seconds and releasing.

5. If the sensor has been successfully linked to the alarm panel, the DISARM LED will turn on for 1 second

and you will hear a long beep. A keypad LED will turn on to indicate the zone number that has been assigned

to the sensor (Numbers 1-9 for zones 1-9, 0 for sensor zone 10 or higher). We advise you to note down the

locaon and the zone number.

6. If binding fails, it will meout aer 30 seconds and 3 short beeps will be heard.

7. To exit the binding process, press the DISARM key.

TESTING

Decide which doors/windows are to be protected by ﬁng magnec contact sensors, (usually the front and

back doors). Addional sensors may also be ﬁed where required to other vulnerable doors or windows, (e.g.

garage, pao doors etc.).

Before mounng, it is wise to ﬁrst test the contact where you want to mount it, to ensure it is within range of

the control panel. To test enable test mode on the alarm panel by entering your PIN + 03 + PARM key.

Next press and release the tamper switch on the back of the sensor when you are holding it near the place

where you want to mount it, you should now hear a chime from the alarmpanel. When you have ﬁnished the

test, press the DISARM key to exit test mode.

-1- -2-

1 2

AAA - 1,5V

Tamper

switch

55mm

32mm

(a)

(b)

(c)

(f)

(d)

(e) (e)

Alternave

mounng

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Elro AG40MA Seite 2

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Elro AG40MA

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info