Bedienungsanleitung Elro AP5500 - Pro Alarm System (Seite 41 von 49) (Englisch)

708667

Zoom out

Zoom in

Vorherige Seite

1/49

Nächste Seite

If the system is disarmed and the ‘ALARM MEM’ LED

is flashing with the panel beeping every few seconds,

this indicates that an alarm condition has occurred.

Use the Event Log to find out and make a note of

where the alarm occurred to assist in tracing the cause

of the alarm.

QUICK SET

To operate the quick set function and fully arm the

system in 5s, overriding the programmed exit delay.

Press

User Password

OMIT ZONE

To omit a zone from the next armed session:

Press

User Password

Scroll through the menu until the required zone is

displayed. The current setting will also be displayed.

To change the setting press .

Press to omit the zone, (i.e. zone omit ON).

Press to re-enable the zone, (i.e. zone omit

OFF).

After configuring zones to be omitted as required

Press to return to Standby mode.

Note: Omitting a zone will only affect the next armed

session. When the system is disarmed the omitted

zones will be re-enabled ready for the next armed

session.

PANIC ALARM

A full Alarm condition can be immediately initiated

at any time (whether the system is Armed or Disarmed)

in the event of threat or danger by activating a Panic

switch on either the Remote Control or the Control

Panel.

Remote Control:

Slide the Panic switch upwards.

Control Panel:

Press and hold the button for approximately

39 3 seconds.

The alarm will continue either for the alarm duration

when the system will automatically reset or until the

system is disarmed.

TAMPER

If the battery cover of any device is removed or if the

Siren or Control Panel are removed from the wall then

a Full Alarm condition will be initiated even if the

system is Disarmed. The alarm condition will continue

either for the alarm duration when the system will

automatically reset or until the system is Disarmed.

The ‘ALARM MEM’ LED on the Control Panel will flash

and the panel will beep every few seconds to indicate

an alarm has occurred.

Note: The Tamper protection facility on the Siren

operates independently. If the Tamper on the Siren is

activated this will not be indicated at the Control Panel.

CHIME

The Chime facility can only be operated with the

system in Standby mode.

Press to toggle the Chime facility between ON

and OFF.

Note: If the Chime is ON and the system is then armed

the Chime will remain ON after the system is disarmed.

EVENT-LOG

The Event Log will store the last 50 system Arm,

disarm, alarm and detector Low Battery events. The

Event Log will record the time, date and details for

each event. If when the system is disarmed the

“ALARM MEM’ LED is flashing and the panel beeps

every 10s, this indicates that an alarm has occurred.

To cancel the LED and stop the beeping you must

access the event log or press to eliminate the

flashing ‘ALARM MEM’ LED and the beeping as well.

To access the Event Log, (with the system in Standby):

Press .

The Event-Log will automatically start scrolling through

and displaying the event data starting with the most

recent event. The data for each event is shown on

two screens, each screen will be displayed for 5

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Elro AP5500 - Pro Alarm System Seite 41

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Elro AP5500 - Pro Alarm System

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info