Bedienungsanleitung Elro AS80PR11 (Seite 3 von 4) (Englisch)

708676

Zoom out

Zoom in

Vorherige Seite

1/4

Nächste Seite

Mounting

The PIR Detector is suitable for mounting in dry interior locations only.

The recommended position for a PIR Detector is in the corner of a room mounted at

a height between 1.8 and 2m. At this height, the detector will have a maximum

range of up to 10m with a field of view of 110° and the position of the PCB set at 5.

The position of the PCB inside the PIR can be set to 5 different positions to adjust

the range of the detector. Setting the PCB in position 3 will reduce the range to

approximately 6m, with position 1 providing a range of approximately 3m. The

recommended position for the PCB is position 5.

When considering and deciding upon the mounting position for the detector, the

following points should be considered to ensure a trouble free operation:

Do not install the detector facing a window, exposed to or facing direct sunlight.

PIR Detectors are not suitable for use in conservatories.

Do not install the detector exposed to ventilators or above a heat source (e.g.

fire, radiators, boilers)

Where possible, mount the detector in the corner of the room so that the path of

an intruder would cut across the fan detection pattern. PIR detectors respond

more effectively to movement across the device than to movement directly

towards it.

Less Sensitive More Sensitive

Do not install the detector in a position where it is subject to excessive vibration.

Ensure that the position selected for the PIR Detector is within effective range of

the system (please refer to the Troubleshooting section).

Note: When the system is armed, household pets should not be allowed into an

area protected by a PIR Detector as their movement would trigger the PIR and

generate an alarm.

Installation

1. Using a 3mm drill, carefully drill out the required mounting holes in the rear

cover according to whether the unit is being mounted in a corner or against a

flat wall.

Note: Drill 1

mounting hole positions to fulfill corner mounting installation, and

mounting hole positions for flat wall installation.

Corner mounting

Using the rear cover as a template, mark the positions of the fixing holes on the

wall.

Fix the rear cover to the wall using the two 18mm No.4 screws and 25mm wall

plugs (a 5mm hole will be required for the wall plugs). Do not over-tighten the

fixing screws as this may distort or damage the cover.

Check that the detector PCB is located and set in the correct position to provide

the required detection range. To adjust the PCB position, simply slide it up or

down ensuring that the location legs are aligned with the required position

number marked on the board.

Refit the detector to the rear cover and locate the clips in the top edge into the

rear cover. Push the lower edge of the detector into place and refit the fixing

screw in the bottom edge of the detector to secure in position. Do not over-

tighten the fixing screws as this may damage the casing.

PCB Position

Range

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Elro AS80PR11 Seite 3

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info