Bedienungsanleitung Elro KT 300RF (Seite 3 von 4) (Englisch)

458152

Zoom out

Zoom in

Vorherige Seite

1/4

Nächste Seite

5. TEMPERATURE SPAN SELECTION

Span is the temperature difference between the turn on

temperature and turn off temperature. For example, in heating

systems, if you set temperature to 20°C and span to 1°C, the

heater will operate when the room temperature drops to 19.5°C

and turns off when the temperature rises to 20.5°C. Set the DIP

switch (position 1 & 2) according to your selection of temperature

span as the following diagram.

6. BATTERY INSTALLATION

Your thermostat uses two (2) "AA" size alkaline batteries to operate. To power-up the

unit, insert two "AA" batteries into the battery compartment of the front housing. When

power is applied for the first time, the display must show time and the day as well as the

room temperature (for example 28.5°C). If the display is different, press the RESET

button. Use a fine probe such as straightened paper clip to gently push the RESET button.

After installation of the batteries, push back the rear housing to the control centre and

then the stand. Before turning on the main switch of the system, press the reset button

once. The thermostat is ready for use.

7. SETTING CLOCK

1.Press the SET TIME button to clear all digits except the day indicator and the time

display. The day indicator is flashing.

2.While day indicator is flashing, press UP or DOWN button to adjust.

3.Press the SET TIME button again, hour digits are flashing instead of day indicator. Press

UP or DOWN button to adjust. Press and hold the UP or DOWN button to speed up the

adjustment rate.

4.Press the SET TIME button again, minute digits are flashing instead of hour digit. Press

UP or DOWN button to adjust. Press and hold the UP or DOWN button to speed up the

adjustment rate.

5.Press the SET TIME button again to return to normal operation mode.

6.The unit will return to normal operation mode if no key is pressed for 10 seconds.

8. SETTING CONTROL TEMPERATURE

1.Press the SET TEMPERATURE button to display the pre-defined set temperature.

2.Press the CONF/ECON button to toggle between the setting of economic mode and

comfortable mode.

3.Press the UP or DOWN button to increase/decrease the set temperature by 0.5°C.

4.Press the SET TEMPERATURE button again to save the set temperature.

5.The unit will return to normal operation mode if no button is pressed for 10 seconds.

6.The default setting of comfortable mode is 21°C for heater mode and 23°C for cooler

mode. And the economic mode is 18°C for heater mode and 26°C for cooler mode.

9. SETTING PROGRAMS * SELECT WEEK-DAY

1.Press the SET PROGRAM button, the day indicator shows the program day and is

flashing. Program number indicator shows the current program for the selected day.

2.Press the UP or DOWN button to select the day needed to program. You can select the

whole week, working day, weekend,or individual day to program.

1 2 Span

ON ON 1°C

OFF ON 2°C

ON OFF 3°C

OFF OFF 4°C

10. SELECT CONTROL PROFILE * PRE-DEFINED

1.Press the SET PROGRAM button indicator stop flashing and the program starts flash.

2.Press the UP or DOWN

button to select the program

profile. P1-P6 are predefined

program, their profile are

shown as follows.

3.If any of these programs is

selected, press the SET

PROGRAM button again to

confirm this program for the

specified day and return to

normal operation mode.

PROGRAMMABLE CONTROL

PROFILE

4.If temperature setting does

not have to be chagend for a

specific hour, pres to go

to the next hour.

Press the button to toggle the control temperature setting and advance the

settinghour digit by one.

EXAMPLE:

button is pressed. Hour Digit (Clock) is 2 and the 02 hour bar is flashing is on

and the operation mode for hour 01 is set to economic mode.

5.Press the button to terminate the setting procedure and to return to normal

operation mode.

EXAMPLE:

button is pressed.Terminate the setting procedure and the new control profile is :

6.The setting procedure will terminate automatically when no button is pressed for 10

seconds.

11. TESTING THE RF TRANSMISSION RANGE

1.Press UP button until the setpoint temperature is higher than room temperature by a

few degrees.

2.Wait for a few seconds.

3.Check the green LED. It should be On.

4.If the LED is not On, try to place the Control Centre closer to the Receiver. Press Down

button to adjust the setpoint temperature to be lower than room temperature to "turn

off" the receiver.

5.Repeat steps 1 to 3.

6.The receiving range between Control Centre and Receiver is 50M in open area. When

placed indoors, this distance may be shorter because of blocking by concrete walls etc,

but is enough for most household applications.

7.Press RESET button after receiving range testing.

00 06 12 18 24

Program 1:

Factory Preset

"Whole day Comfort"

Program number Program profile

Program 2:

Factory Preset

"Whole day Econ"

Program 4:

Factory Preset

"Whole day (A)"

Program 5:

Factory Preset

"Whole day (B)"

Program 6:

Factory Preset

"Half-day work"

Program 3:

Factory Preset

"Holiday"

00 06 12 18 24

-5- -6-

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Elro KT 300RF Seite 3

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Elro KT 300RF

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info