1. The Converter unit is operated by 1 x 12 volt battery (23A - included).
2. Remove the back of the case by pushing in the tab on the bottom with a
small, flat screwdriver.
3. Insert 1 x 12 volt battery (23A - included) in the battery compartment, ensuring
the battery’s polarity matches the internal markings.
4. Snap the front cover of push button back on, then it is ready to use.
Installation Guide
1) Westminster - 8 notes
2) Ding-Dong - Repeat
3) Telephone Ring
4) Circus Theme
Melody Selection (On selected Models)
The Melody selector is located inside the push converter unit, a small switch on the
top left corner of battery compartment marked with “S”. Press the switch once, the
melody will change to the netxt one on the list, there are a total of 8 melodies for
selection. The converter is pre-set to “Westminster” therefore, if no change is
required, it should not be adjusted.
5) Banjo on my knee
6) Twinkle, Twinkle
7) It’s a small world
8) Dog Barking
1. Drill hole and fit wall plug (if fixing to masonry) and screw (self-tapping N3 x 16mm
screw) to fixing position. Leave a gap of 3mm between the screw head and the wall.
Locate the keyhole slot on the back of the unit, over the screw.
Important: Mounting the Converter unit on metal or UPVC doorframes will seriously
reduce the operating range.
2. Then use the second hole located at the bottom half of the Converter as a template,
mark the fixing position for the unit. Drill hole and fit wall plug and secure the Converter
Unit with the screw (self-tapping N3 x 16mm screw) in position.
3. Alternatively, use the double-sided self-adhesive pad (included) to attach the converter
to the fixing position between the bell push and door chime unit.
Note: When mounting to masonry, fit wall plugs. When mounting to wooden doorframe
wall plugs are not necessary.
In case a Transformer (A/C 8v) is used to power the Wired Bell
Push and Wired Door Chime.
1. Remove the back of case by pushing in the tab on the botton
with a small, flat screwdriver.
2. Disconnect the wire that connected with Wired Door Chime.
3. Feed the wire via the hole on the back of the Converter,
connect the wire to the terminal positions marked below.
4. Snap the front cover of push button back on, then it is ready
to use.
Important: Do not connect the Converter unit with any Lighted
Bell Push.
Operation
When the wired Bell Push is pressed, it will activate the
Converter and transmit a wireless signal for 1 second to the
Wireless Door Chime, Green LED light will light up as operation
indication, and the door chime will sound.
Important
1. Do not mount the Converter unit onto any metal surface or metal doorframe including UPVC.
2. Do not expose the unit directly to rain or immerse either in water.
3. Do not expose the unit to high temperatures or close to fireplace.
4. Do not leave exhausted batteries in either unit.
5. Do not connect the Converter unit with any Lighting Bell Push.
6. Converter is designed for internal use only.
7. Please dispose of old, defective batteries in and environmentally friendly manner in accordance with the
relevant legislation.
8. Make sure that no naked flame sources, such as lighted candles, should be placed on the unit.
9. The unit should not be exposed to dripping or splashing and that no objects filled with liquids.
10. Replace only with the same or equivalent type battery recommended by the manufacturer.
Specification
Converter unit
Power
Consumption
Operating Temperature
Operating Distance
Selectable Tone
Selectable Channel
: 1 x 12volt 23A battery (included) Replace with Byron SD100 model.
: 3.0mA - ON
0.003mA - OFF
: -10°C to +40°C
: 100 metres (320 feet approx.) in open field
: Total eight (8) tones available
: Total sixteen (16) possible channels
The unit comes from the factory on a pre-set radio frequency channel.
However, should you door chime activate intermittently for no reason at all,
it is possible that a similar unit is operating nearby on the same frequency.
The encoded frequency of the Converter (transmitter) and Door Chime
(receiver) can be changed to avoid this problem.
1. Remove the back of the case by pushing in the tab on the bottom with a small, flat screwdriver.
2. There is a 4 position dip switch marked 1,2,3,4. Use a small screwdriver to alter the dip switch levers to
the “On/Off” position, which can be altered to achieve a total sixteen (16) possible channels.
3. In any combination ensuring it is set to the same code on both Converter and Wireless Door Chime units.
4. Test to ensure correct operation before final installation.
Channel Selection
B+C SWITCH
A+C 8V/AC
B+C SWITCH
SX
Chime
unit
WIRED
CHIME
(Transformer
operation)
4
T
Converter
unit
SX
Chime
unit
WIRED
CHIME
(Transformer
operation)
3
T
Converter
unit
SX
Chime
unit
1
Converter
unit
SX
Chime
unit
WIRED
CHIME
(Battery
operation)
2
Converter
unit
Please note that these diagrams are only for reference
as a guide.
EACH Wired chime can be wired differently, so if you
encounter problems, PLEASE CALL THE HELPLINE ON
0121 5449499
Wiring Installation
The Converter is designed to change your existing Wired Bell Push to wirefree.
1. Simply connect your Wired Bell Push with the cable from Converter to the terminals on your bellpush.
2. Your Wired Bell Push with Converter is ready to use.
B and C
A and C
A and C
A and C
Wired Bell
Push
Converter unit
Brauchen Sie Hilfe? Stellen Sie Ihre Frage.
Missbrauch melden von Frage und/oder Antwort
Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.
Art des Missbrauchs:
Forenregeln
Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:
Lesen Sie zuerst die Anleitung;
Schauen Sie nach, ob die Frage bereits gestellt wurde;
Stellen Sie die Frage so deutlich wie nur einigermaßen möglich;
Erwähnen Sie was Sie bereits versucht haben um das Problem zu lösen;
Ist Ihr Problem von einem Besucher gelöst dann lassen Sie ihn / sie wissen in diesem Forum;
Falls Sie reagieren möchten, so verwenden Sie bitte das Antworten- Formular;
Da ihre Frage für alle Besucher sichtbar ist, sollten Sie lieber keine persönliche Daten erwähnen.
Neu registrieren
Registrieren auf E - Mails für Elro SX32 wenn:
neue Frage gestellt werden
neue Handbücher vorhanden sind
Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.
Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.
Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.
Ihre Frage wurde zu diesem Forum hinzugefügt
Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.
