Bedienungsanleitung Emerio CH-102597.6 (Seite 6 von 25) (Deutsch, Englisch, Französisch, Italienisch)

701495

Zoom out

Zoom in

Vorherige Seite

1/25

Nächste Seite

- 5 -

CH-102597.6 EN

ASSEMBLY OF THE HEATER

Before using the heater, the feet (supplied separately in the box) must be fitted to

the unit. These are to be attached to the base of the heater using the 4 self-tapping

screws provided, taking care to ensure that they are located correctly in the bottom

ends of the heater side moldings.

OPERATION OF THE HEATER

Note: When the heater is turned on for the first time, or when it is turned on after a longer period of storage, it

is normal that the heater may emit some smell and fumes. This will disappear when the heater has been on a

short while.

 Set the thermostat to the minimal position and insert the plug to the power supply.

 Turn on the power switch: 750W, 1250W, 2000W.

 Turn the thermostat knob in a clockwise direction to the max position.

 Once the room temperature has reached the desired value, turn the thermostat knob slowly in anti-

clockwise direction until you hear a "click" sound; this is the setting temperature.

 The appliance will automatically maintain the setting temperature. It will switch on when the room

temperature is below the setting, and switch off if it is above the setting.

CONVECTOR HEATER WITH THERMOSTAT AND FAN

This heater incorporates an internal fan, to be switched independent from the heating elements.

Press the switch to turn on the fan. The fan will only operate with the thermostat in the on position. It can

be used when the heating elements are on to blow warm air into the room. In warm conditions the fan can be

used with the heating elements off to blow cool air into the room.

SAFETY SYSTEM

The appliance has a safety system which automatically switches off the unit when overheated, for example, due

to the total or partial obstruction of the vents. In this case, switch off the appliance, remove the plug from the

socket. Let it cool down for about 30 minutes and remove the object which is obstructing the vents. Then put

the plug in the socket and switch on the heater. It should now operate normally.

CLEANING THE HEATER

1. Always unplug the heater from the wall socket and allow it to cool down completely before cleaning.

2. Clean the outside of the heater by wiping with a damp cloth and with a dry cloth.

3. Do not use any detergents or abrasives and do not allow any water to penetrate the heater.

STORING THE HEATER

When the heater is not used for a long time it should be protected from dust and stored in a clean dry place.

TECHNICAL DATA

Supply voltage: 220-240V ~ 50-60Hz

Power consumption: 2000W

GUARANTEE AND CUSTOMER SERVICE

Before delivery our devices are subjected to rigorous quality control. If, despite all care, damage has occurred

during production or transportation, please return the device to your dealer. In addition to statutory legal rights,

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Emerio CH-102597.6 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info