Bedienungsanleitung Emerio PH-122174 (Seite 6 von 45) (Deutsch, Englisch)

701980

Zoom out

Zoom in

Vorherige Seite

1/45

Nächste Seite

PREPARATION FOR USE

The appliance uses ordinary tap water.

If the water is very hard (hardness higher than27 degrees French).we suggest using distilled or de-

mineralized water.

Before using equipment, open the flap of water (15), added just the right amount of water to the

water tank (14), first is less than the MAX water level.

Connecting the appliance and power cord.

Press the main switch (8), power indicator light (8) lights up, it means the iron start running. In the

condition of the equipment only dry hot function.

At the same time, press the boiler switch (6), the boiler power light (6) and steam available indicator

light (7) light up, it means the boiler (12) start running. The appliance is the steam mode.

Feed-water from electromagnetism water pump coming down the boiler when the boiler(12) heating

enough. Choosing the temperature by temperature knob(3),the colored part indicate ironing area

which can be chose.

Around 90 seconds . Heating indicator(4) will die out , it means the appliance can be using the steam.

Around 3 minutes. Steam available light (7) will die out, it means the appliance can be using the

steam.

If you exit out the steam mode, you just press again the boiler switch button(6), the boiler power

indicator light (6) goes out, it means the appliance exits out the steam mode.

Cheak the manufacturer’s label on the garment, and interpret the symbol on the label as follows.

STEAM IRONING

When using the iron for the first time, iron a plain cloth first.

Obtain steam after pressing the steam button (2).

This appliance is also able to generate steam in a vertical position and can therefore be used to refresh

fabrics easily with a jet of steam.

If you hear the loud feed-water sound when you ironing, it means there is no water in the water

tank(14).Press the boiler button(6) and cut down the boiler power . After fill the water tank(14),then

press the boiler button(6) again ,go on ironing.

CAUTION! Never attempt to open the cleaning valve(10) while the boiler is under pressure.

DRY IRONING

Connect the appliance to the mains supply, only press the main switch(8), then select the desired

temperature by turning the thermostat knob(3).Wait until the iron heating indicator light (4) goes off,

indicating that the desired temperature has been reached.

PUTTING THE APPLIANCE AWAR

- After use, always allow the iron to cool before putting it away.

- It is not necessary to drain the boiler after ironing.

- Position the Steam flexible hose- Power cable get together in the base of the appliance（10）.

- Always keep the surface the ironing plate perfectly clean. To clean it, just wipe the cold surface with

a damp cloth. The appliance must not be cleaned with descaling agents.

- Do not iron over zippers, hooks, rings, etc; as these may scratch the plate.

- When you have finished ironing. Place the iron correctly on its stand. Ensure that there are no traces

of water under the plate, as these may cause stains.

- Store the appliance in a dry place

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Emerio PH-122174 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info