Bedienungsanleitung Emerio WK-109469 (Seite 6 von 39) (Deutsch, Englisch, Holländisch, Französisch, Polnisch, Schwedisch)

678637

Zoom out

Zoom in

Vorherige Seite

1/39

Nächste Seite

- 5 - WK-109469

HOUSEHOLD USE ONLY

PARTS DESCRIPTION

1. Lid opening button

2. Handle

3. Water gauge

4. On/off switch (a) and adjustable

temperature control (b)

5. Power base

6. Anti-calc filter

BEFORE USING YOUR KETTLE

If you are using the kettle for the first time, it is recommended that you clean your kettle before use by boiling

a full kettle of water twice and then discarding the water.

OPERATION OF YOUR KETTLE

1. Open the lid; fill with the desired amount of water to the water kettle. Always fill the kettle between the

minimum (0.5L) and maximum (1.8L) marks. Too little water will result in the kettle switching off before

the water has boiled.

NOTE: Do not fill the water over the maximum level, as water may spill out of the spout when boiling.

Ensure that the lid is firmly in place before connecting the power cord to the outlet.

This water kettle is equipped with an overfill safety feature. This will make sure that in case of overfilling

the kettle the water will not come in contact with electrical components of the kettle ensuring no unsafe

situations can occur. In case of overfill the water will be lead through the inner side of the kettle and will

exit the kettle at the bottom, away from the electrical element.

2. Connect the plug into a power outlet. Press the on/off switch button “ ” on the handle and the kettle

starts to boil the water. The LED light will be shining in red. The kettle will switch off automatically once

the water has boiled. You can shut off the power by pressing the switch button again at any moment

during boiling water.

NOTE: Ensure that switch is clear off obstructions and the lid is firmly closed. The kettle will not turn off if

the switch is constrained or the lid hasn’t been closed.

3. Take the plug out of the outlet. Lift the kettle then pour the water.

NOTE: operate carefully when pouring the water from your kettle as boiling water will scald.

4. The kettle will not re-boil until the switch is pressed again. Allow to cool for 30~40 seconds before

reopening to boil water.

NOTE: Ensure power supply is turned off when kettle is not in use.

5. Should you accidentally allow the kettle to operate without water; the boil-dry protection will

automatically switch it off. If this occurs, allow the kettle to cool before filling with cold water and

re-boiling.

Advanced operation:

1. Keep warm function:

Press the on/off switch for 3 seconds until a “beep” sounds; the kettle will be shining with red light on and

off. After the water boils, the kettle will keep it warm for 2 hours and go on heating when the temperature

drops below 85°C .

2. Temperature showing by LED display:

Use the adjustable temperature control to choose the desired water temperature. When the

desired temperature reaches, the kettle will stop heating.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Emerio WK-109469 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info