Bedienungsanleitung EMOS 5002 (Seite 5 von 48) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Schwedisch, Norwegisch, Finnisch)

784675

Zoom out

Zoom in

Vorherige Seite

1/48

Nächste Seite

USING ALARM AND SNOOZE FUNCTION

1. Set the desired alarm time as described in the above section.

2. Or press “ALARM” key to display the alarm time, press it again to turn on alarm

function with the alarm icon “ ” displayed on the LCD.

3. When clock reach the alarm time, alarm sound will start.

Where it can be stopped by following operation:

a) Auto-stop after 2 minutes alarming if without any operation and the alarm will activate

again in the next day.

b) By pressing [ ALARM / SNOOZE ] key to enter snooze that the alarm will sound again

after 5 minutes.

c) By pressing and hold [ ALARM / SNOOZE ] key for 2 seconds to stop the alarm and

will activate again in the next day

d) By pressing [ ALARM ] key to stop the alarm and the alarm will activate again in the

next day.

Note:

- The snooze could be used continuously in 24 hours.

- During the snooze, the alarm icon “ ” will keep ashing.

TEMPERATURE FUNCTIONS

1. Press [ °C / °F ] key to switch between °C /°F temperature unit.

2. When the temperature is below -50°C or above 70°C, “Lo” or “Hi” will be displayed

respectively.

Above 70°C Below -50°C

TEMPERATURE AND HUMIDITY TREND

The temperature and humidity trend indicator shows the trends of changes in the

forthcoming few minutes. Arrows indicate a rising, steady or falling trend.

Arrow indicator

Trend Rising Steady Falling

COMFORT INDICATION

The comfort indication is a pictorial indication based on indoor air temperature and

humidity in an attempt to determine comfort level.

Too cold Comfortable Too hot

Note:

- Comfort indication can vary under the same temperature, depending on the humidity.

- There is no comfort Indication when temperature is below 0°C(32°F) or over 60°C

(140°F).

THE SNOW ICON

When the outdoor temperature is 3°C or below, the

ashing snow icon will appear in outdoor section.

WEATHER FORECAST

The device contains sensitive pressure sensor built-in with sophisticated and proven

software that predicts weather for the next 12 ~ 24 hours within a 30 to 50 km (19-31

miles) radius.

Sunny / Clear Slightly Cloudy Cloudy

Rainy Snowy

Note:

1. The weather forecast is meant for the next 12 - 24 hours, it may not necessarily

reect the current situation.

2. The weather icon will ash on display when the rainstorm comes.

3. The SNOWY weather forecast is not based on the atmospheric pressure, but based

on the outdoor temperature. When the outdoor temperature is below -3°C (26°F),

the SNOWY weather indicator will be displayed on the LCD.

BAROMETRIC/ATMOSPHERIC PRESSURE

TO SELECT THE DISPLAY MODE

Press and hold the [ BARO ] key for 2 seconds to toggle between:

ABSOLUTE the absolute atmospheric pressure of your location

RELATIVE the relative atmospheric pressure based on the sea

TO SET RELATIVE ATMOSPHERIC PRESSURE VALUE

1. Press and hold the [ BARO ] key for 2 seconds until ABSOLUTE or RELATIVE icon

ashes.

2. Press [ CHANNEL / + ] key or [ MEM / - ] key to switch to RELATIVE mode.

3. Press the [ BARO ] key once again until the RELATIVE atmospheric pressure digit

ashes.

4. Press [ CHANNEL / + ] key or [ MEM / - ] key to change the value.

5. Press the [ BARO ] key to save and exit the setting mode.

Note:

- The default relative atmospheric pressure value is 1013 hPa (29.92 inHg), which

refers to the average atmospheric pressure.

- When you change the relative atmospheric pressure value, the weather indicators will

change along with it.

- The relative atmospheric pressure is based on the sea level, but it will change with the

absolute atmospheric pressure change.

TO SELECT THE MEASUREMENT UNIT FOR THE BAROMETER

1. Press the [ BARO ] key to enter unit setting mode.

2. Use the [ BARO ] key to change the unit between inHg / mmHg / hPa.

3. Press the [ BARO ] key to conrm.

HEAT INDEX / DEW POINT

TO VIEW HEAT INDEX

Press the [ INDEX ] key repeatedly to show HEAT INDEX

value.

Note:

Heat index is only calculated when temperature is 27° C (80° F) or above, and based

solely from the temperature and humidity measured from the outdoor wireless sensors.

TO VIEW DEW POINT

Press the [ INDEX ] key repeatedly to show DEW POINT

value.

Note:

The dew point is the temperature below which the water vapor in air at constant

barometric pressure condenses into liquid water at the same rate at which it evaporates.

The condensed water is called dew when it forms on a solid surface. The dew point

temperature is calculated from the outdoor temperature and humidity measured at the

outdoor wireless sensors.

HISTORY DATA (WEATHER RECORDS IN THE PAST 24 HOURS)

The main unit will record past 24 hours weather data automatically that included past

indoor and outdoor temperature & humidity, Baro, and Dew point / heat index records.

1. Press the [ HISTORY ] key to check past 1 hour history records.

2. Press [ HISTORY ] key repeatedly to show past 2, 3, 4 , 5.......24 history weather

records.

MAX/MIN RECORD

The main unit preserves the MAX/MIN weather data records since the last manual reset.

1. In normal mode, press [ MEM / - ] key once to show the current channel’s maximum

temperature.

2. Press [ MEM / - ] key repeatedly to show the MAX/MIN reading in this order: current

channel’s maximum temperature current channel’s minimum temperature

current channel’s maximum humidity current channel’s minimum humidity

indoor maximum temperature indoor minimum temperature indoor

maximum humidity indoor minimum humidity maximum baro reading

minimum baro reading

3. When the MAX/MIN records are shown, the display will return to normal mode after

leaving the unit for 6 seconds.

4. To erase the MAX/MIN records of indoor or current channel, press and hold [ MEM

/ - ] key for 2 seconds when the unit is displaying MAX/MIN records.

ALERT SETTING AND DISPLAY

The unit can setup temperature HI/LO alert for indoor and up to 8 outdoor

channels.

1. In normal mode, press and hold [ ALERT ] key for 2 seconds to enter alert setting

mode and the “IN” icon will ash. Press [ CHANNEL / + ] or [ MEM / - ] key

again to choose outdoor channel.

2. Press [ ALERT ] key to switch between channel, temperature HI, temperature LO,

humidity HI and humidity LO alert setting.

3. Press [ CHANNEL / + ] or [ MEM / - ] key to modify the value by 0.1 °C/°F for

temperature or 1% for humidity, you can also press and hold to quick adjust the

value.

EMOS 5002 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info