Bedienungsanleitung EMOS 6016 (Seite 5 von 92) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Schwedisch, Norwegisch, Finnisch)

784678

Zoom out

Zoom in

Vorherige Seite

1/92

Nächste Seite

unit of precipitation: mm/inch

radio signal range: to 100 m in open area

number of sensors which can be connected: max. 3 (temperature/humidity/wind sensor), max. 1

(precipitation sensor)

wireless sensor: transmission frequency 433 MHz, 10 mW e.r.p. max.

station power supply: 3× 1.5 V AAA batteries (not included)

adapter AC 230 V/DC 5 V, 300 mA (included)

temperature/humidity/wind sensor power supply: 4× 1.5 V AA (not included)

precipitation sensor power supply: 2× 1.5 V AA (not included)

station dimensions and weight: 17 × 192 × 127 mm, 364 g

temperature/humidity/wind sensor dimensions and weight: 275 × 135 × 310 mm, 377 g (without

batteries)

precipitation sensor dimensions and weight: 100 × 106 × 166 mm, 220 g (without batteries)

Getting Started/Installation

1. Plug the power adapter into the station, then insert batteries rst into the weather station and then

into: wireless temperature/humidity/wind sensor and wireless precipitation sensor. The battery

compartment of the precipitation sensor is protected by screws; use a suitable screwdriver.

2. When inserting the batteries make sure the polarity is correct to avoid damaging the weather

station or sensors. Only use alkaline batteries of the same type; do not use rechargeable batteries.

3. Place all the units next to each other. The weather station will automatically detect the signal

from sensors within 3 minutes. If signal from sensors is not detected, long-press the button

on the weather station to repeat the search and press the TX button on the sensor.

4. To ensure correct measurement, the temperature/humidity/wind sensor and precipitation sensor

must be placed above the ground surface (at least 1.5 m) onto a horizontal surface and outside

of buildings and structures. Both sensors must be rmly screwed on to prevent their damaging.

First, screw the mounting plate onto a level surface, then mount the mounting rod into it. Screw

the temperature/humidity/wind sensor onto the rod. Wind must ow freely around the wind

sensor from all sides. Check that the wind direction indicator and paddles for measuring wind

speed can rotate freely. The north arrow (N) on the built-in compass must point to the real north.

Otherwise, wind direction will always be displayed incorrectly. When choosing a suitable place for

mounting the sensor, check before installation that the main station is within range of the sensors.

The range of the sensors may decrease substantially in areas with large number of obstacles.

5. Do not place the sensors onto metal objects as this will reduce their transmission range.

6. If the low battery icon is displayed, replace batteries in the sensors or weather station.

Changing Channel and Connecting Additional Sensors (Valid for Temperature/

Humidity/Precipitation Sensor)

1. Choose the desired channel 1, 2, or 3 for the sensor by repeatedly pressing the button. Then,

long press the button; the icon will start ashing.

2. Remove the cover from the battery compartment on the rear of the sensor and set the sensor

switch to the desired sensor channel number (1, 2, 3), then insert batteries (4× 1.5 V AA). Data

from the sensor will be loaded within 3 minutes.

3. If sensor signal is not found, remove the batteries and proceed again in accordance with steps

1 and 2 or press the TX button.

Attention:

The anemometer (wind speed and direction measurement) only functions on channel 1 (spare

sensor E06016).

Channels 2 and 3 are used for information about outdoor temperature and humidity (spare sensor

E06018).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

EMOS 6016 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info