Bedienungsanleitung Emphaser EA2160 (Seite 14 von 36) (Deutsch, Englisch)

64741

Zoom out

Zoom in

Vorherige Seite

1/36

Nächste Seite

1 1

4. WIRE ROUTING

Important! There must not be a direct contact of the amplifier heatsink, bottom

panel or any other metal part of the amplifier to the vehicle! Electrical ground-

loops can result in audible hum!

4.1 MAIN POWER WIRES

Run the positive main power cable („+12 V“) directly from the positive terminal of the car battery to

the amplifier. For protection of your car audio system against electrical fire hazards, resulting from a

short-circuit of the main power cable to chassis ground a main fuse holder must be inserted

within the first 30 cm of the positive main power cable. The applicable fuse value must

be matched to the limitations of your main power cable AND the current draw of the amplifier – there-

fore choose an appropriate fuse value.

Attach the ground cable to the amplifier. In most cases it will be best to keep the ground

cable („-12V“) as short as possible, i.e. to find a chassis contact very close to the amplifier. The ground

power wire must have the same cross-section as the positive power cable. The contact point where the

ground wire is attached to, must be solid and clean, i.e. free from rust or paint!

Tighten both power input terminals of the amplifier, and double check for perfect fit of both main

cable leads!

4.2 RCA & REMOTE WIRES

Carefully run the audio signal interconnects, the remote wire and – if applicable - the cable of the low

pass level remote control from the head-unit or dashboard to the amplifier. As mentioned before, the

audio signal cables should always be routed completely separate from the power cables. Connect the

remote (turn on/turn off) lead to the respective input terminal of the amplifier and to the remote output

of your head-unit. Now you can connect the RCA interconnects to the respective outputs of your head-

unit and to the inputs of the amplifier. Pay attention to connect the stereo interconnects correspondingly,

left is 1CH, right is always 2CH a.s.o.

If you want to drive a subwoofer system with your amplifier, you can install the remote low pass level

remote control in a convenient position under or besides the dashboard.

4.3 LOUDSPEAKER WIRES

Once the speaker cables have been routed, turn loose the screws of the speaker terminal binding

posts and – after inserting the stripped speaker cables – re-tighten the screws. When baring wires for

connection, remove approximately 6-8mm of the insulation and after axially twisting the wires, insert

the bare ends into the corresponding speaker terminal output on the amplifier. Maintain correct

polarity („A“ to „A“; „B„ to „B„).

Close the electrical circuit by inserting the main fuse. Now switch on your head unit. The green

OPERATING LED of the amplifier should light-up. If the LED lights up red, your installation is wrong!

Immediately turn off your head-unit and carefully re-check all installation steps!

EA 2-4-5 CH Manual (EDF).indd 14 01.03.2006 9:30:23 Uhr

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Emphaser EA2160 Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info