691900
10
Zoom out
Zoom in
Vorherige Seite
1/16
Nächste Seite
9/15 EmpirBus NXT DCM User manual Ver 1.53
7.3.2!Manual!override!switch!on!
1. Press the right arrow button. ”SEL” will be shown in the display.
2. Use the right arrow button to step to the desired channel.
3. Press and hold MAN ON/MAN OFF for three seconds
4. If the channel indicator still is flashing red, again press and hold MAN ON/MAN OFF for three
seconds
5. Press the left arrow until the message “SEL” in the display disappears.
6. Outputs manually switched off are now indicated with flashing green indication.
7.3.3!Resetting!a!channel!
1. Press the right arrow button. ”SEL” will be shown in the display.
2. Use the right arrow button to step to the desired channel.
3. Press and hold RESET/AUTO for two seconds. The channel is now reset.
4. Press the left arrow until the message “SEL” in the display disappears.
7.4!Wireless!transmitter!pairing!
If the DCM is equipped with a wireless receiver, the transmitters (switches/remotes/detectors etc.)
need to be paired with the unit in order to operate. Each transmitter needs to be paired to a unique
function number.
1. Press and hold MAN ON/MAN OFF for 10 seconds until the display shows “P00”.
2. Use right arrow button to step to “P10” for wireless receiver programming.
3. Press MAN ON/MAN OFF Once. Display shows “OAS” / “001” blinking. Wireless channel 1 is
selected.
4. Use right arrow button to choose channel (if other than 1).
5. Press MAN ON/MAN OFF to enter learning mode. Display flashes “LEA”.
6. Press the wireless switch (or trigger the detector) that is to be connected.
7. When button has been pressed the display alternates between “LEA” and “ACC” for five
seconds to indicate that the transmitter was learned and accepted.
8. The DCM auto detects the type of transmission from the transmitter and suggests a setting:
“FU1” or “FU2”. (FU1 = transmitter sends “pressed” and “released”, FU2 = transmitter sends
only “pressed”.)
Press MAN ON/MAN OFF to accept the setting and continue. If additional transmitters need
to be paired, repeat from step 3.
9. Press RESET/AUTO to exit programming mode and return to normal mode.
How to delete a paired wireless channel:
Enter the programming mode P10 as mentioned above from point 1 to 3.
Use right arrow key to select the channel you want to erase (1 to 30 ).
Press MAN ON/MAN OFF once to enter learning mode.
Press and hold in MAN ON/MAN OFF (the textddd will appear on the display) until is
showsdel” then release the button.
Press MAN ON/MAN OFF once, the textdcd” on the display then confirm that the channel is
erased.
10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für EmpirBus NXT DCM wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info