Bedienungsanleitung Enersys ODYSSEY Battery Charger (Seite 10 von 14) (Englisch)

660387

Zoom out

Zoom in

Vorherige Seite

1/14

Nächste Seite

General Operation

Charging a 12V Flooded or AGM (Absorbed Glass Mat) Lead Acid Battery.

Observe the instructions and safety information of the vehicle to find out how the vehicle

battery should be charged. Modern vehicles are equipped with sensitive electronic parts

and controls that can be damaged if you do not proceed properly.

a) First make sure your battery is a 12 volt flooded or AGM (Absorbed Glass Mat) lead acid

battery. Do not charge batteries with different operating voltages or chemistries.

b) Determine the chemistry of your battery. This should be on the battery or contact the

battery manufacturer. This charger is for flooded and AGM lead acid batteries.

c) If the battery is installed in a vehicle, turn off the ignition and any other loads.

d) When the battery cables are connected per the instructions in this manual, and the

charger is plugged in to AC power (115 V 60 Hz AC), the battery monitor and the

AC power LEDs will illuminate.

e) If the Battery Trouble Status LED is illuminated, unplug AC connection of the charger

from the electric outlet, check to make sure the connections are secure and the polarity

of the cables to the battery is correct. Plug the charger back into the electric outlet. If

the Battery Trouble Status LED continues to illuminate there is a problem with the battery.

f) There will be up to a two minute check process to make sure connections and the battery

are correct, then the charger will start the charge. When the charge cycle starts, the

Charge Monitor LEDs will illuminate letting you know the battery charge level.

g) When all five charge monitor LEDs are illuminated the charge is complete and the charger

can be disconnected first from the AC power then the DC connection removed by first

removing the negative clamp or connection followed by the positive clamp or connection.

h) See typical set up illustrations for in-vehicle and out-of-vehicle set up and use.

General Operation

Typical Setup - Charging In-Vehicle - Negative Chassis Ground

WARNING - Read and Follow all INSTRUCTIONS. FAILURE TO FOLLOW INSTRUCTIONS

MAY CAUSE SERIOUS INJURY, DAMAGE OR EXPLOSION, ALWAYS WEAR SAFETY

GLASSES.

Read and follow all General and Personal Safety Precautions in this manual and those

by the battery manufacturer.

Read and follow all the preparing to charge steps for in a vehicle battery charging.

Below please find the typical steps for in a vehicle charging NEGATIVE (NEG, N, – ) chassis

ground vehicles.

a. Connect the red POSITIVE (POS, P, +) cable clamp to the POSITIVE (POS, P, +) post.

b. Connect the BLACK NEGATIVE (NEG, N, –) cable clamp to the vehicle’s chassis.

Do not connect the black negative (NEG, N, –) cable clamp to metal fuel lines or

anywhere in proximity of the carburetor or the battery itself.

c. Plug the charger into a properly grounded fault protected outlet.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Enersys ODYSSEY Battery Charger Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info