619944
11
Zoom out
Zoom in
Vorherige Seite
1/65
Nächste Seite
10
Only experienced installation professionals who are familiar with outdoor
wireless network should attempt to install the ENH700EXT.
2.1 Installation Considerations
There are many considerations on where to place the ENH700EXT. The followings are the main
considerations on where to mount the device. The first consideration is available line of sight to
the area or building that you wish to provide wireless network connectivity. Other buildings,
mountains, hills, trees, thick brush can all attenuate the or inhibit the wireless signal.
The second consideration is distance. You should calculate the EIRP (Effective Isotropic
Radiated Power) correctly to properly configure the ENH700EXT using this calculation for the
distance you intend to build the wireless link (see Glossary at the end of this manual for the
EIRP formula). Don't place multiple ENH700EXT’s too far away from one another since the AP
uses default Omni directional (not directional) antennas. If you plan to have a longer range
connection, you can consider identically-matching directional antennas to connect to the
ENH700EXT on both transmit and receiving ends.
2.2 Assembling the ENH700EXT
Carefully remove the ENH700EXT unit, the Omni 5dBi and 2.4dBi Antennas(two each), EPE-
48GR PoE Injector, and power adaptor. As mentioned earlier in this Manual, the Ethernet cables
are required and not provided within the ENH700EXT package.
1. Install all 4 antennas onto the ENH700EXT by screwing them toward the ENH700EXT
until the threads on the screw are not visible.
2.
Ensure that all antennas screw on straight. Failure to do so may
damage the ENH700EXT antenna connectors
3. Insert a shielded Ethernet cable into the RJ-45 port on the ENH700EXT. You need to
consider the length of this cable based on the distance from where the PoE injector is
which in a weather protected place such as indoor or a water tight box to the
ENH700EXT. Use high quality cable is highly recommended.
4. Insert the other end of the Ethernet cable to the EPE-48GR PoE Injector on the port
labeled AP/Bridge.
5. Take a second Ethernet cable and connect it to the Network port of the EPE-48GR PoE
Injector.
11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Engenius ENH700EXT wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info