Bedienungsanleitung Engenius EP800 (Seite 10 von 351) (Deutsch, Holländisch, Französisch, Italienisch, Spanisch, Polnisch, Türkisch)

619916

Zoom out

Zoom in

Vorherige Seite

1/351

Nächste Seite

~19~

24.

Programmable Flash key timing

a. From MENU-6-2 to select flash key timing

b. 9-level (100 ms - 900 ms) timing selections, default= 600 ms.

c. The default value (600 ms) works in most areas. Changing this

setting may cause Flash key not working. Change only when you

are certain of the new value would work.

d. When entering the Base Settings, PIN is required. Default is “0000”.

25.

Assign next handset ID for new handset

Using registered handset from MENU-6-3 to assign a next handset

ID to a new handset.

b. If not assign next handset ID, the system will automatically assign a

handset ID to a new handset..

c. When entering the Base Settings, PIN is required. Default is “0000”.

26.

Clear Handset

Using registered handset from MENU-6-4 to remove the other

registered handset, in case the other registered handset is defected.

b. Once clear the other registered handset, the user is able to register a

new handset for instead.

c. When entering the Base Settings, PIN is required. Default is “0000”.

27.

Change PIN

Allow changing the base PIN which requires entering the “Base Settings”

(MENU-6-5).

Using registered handset to change PIN from MENU-6-5.

b. Default PIN is “0000”.

c. When entering the Base Settings, PIN is required. Default is “0000”.

28.

Auto Hang Up feature

Using registered handset from MENU-6-6 to turn on/off the Auto

hand up feature.

b. If turning on the feature, the handset will automatically hang up the

call when the far-end hangs up the call.

c. When entering the Base Settings, PIN is required. Default is “0000”.

29.

Area Code

The area code function allows calls within local and country area codes

to be dialed without the prefix.

a. Enter MENU-4-7-1 to set the “Local” area code.

Enter MENU-4-7-2 to set the “Country” area code.

Re: Up to 3 digits can be entered.

~20~

30.

Multiple Base setting

Up to 4 base stations can be set in one system.

Re:

For best performance, maintain a distance of at least 5 meters

(about 15 feet) between any two base stations.

31.

Set Time

The set time function allows user to set date/time to support the DTMF

caller ID (DTMF caller ID doesn’t attach date/time when receiving from

PSTN, using this setting, user is able to review the date/time when the

caller ID received).

a. Enter MENU-6 to set Base Settings.

Press or scrolling key to select desired base station

when Multi-Base is set.

c. Enter Base PIN (Default is “0000”).

d. Enter “7” to enter Set Time.

e. Enter 4 digits for MM/DD(Month/Day), then enter 4 digits for hr:mm

(Hour：Minute)

f. Press SAVE (left soft key) to finish the setting.

32.

Mic Gain

Allow changing the handset microphone gain based on the handset in

different environment – Quiet, Normal and Noisy environment.

This requires entering the “Phone Settings” (MENU-5-1).

33.

Headset Ring

Allow changing the ringer emitted either from handset speaker or

receiver of headset.

This requires entering the “Phone Settings” (MENU-5-9).

34.

Baby Monitor

Allow setting the handset monitoring the baby room via intercom call.

When setting Baby Monitor ON, this dedicated handset will not answer

any incoming call, except the 2-way intercom.

This requires entering the “Call Settings” (MENU-4-5).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Engenius EP800 Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Engenius EP800

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info