Bedienungsanleitung Engl Screamer 50 (Seite 4 von 6) (Englisch)

693628

Zoom out

Zoom in

Vorherige Seite

1/6

Nächste Seite

A TIP from the Designer: If you want to control the amplifier via a MIDI system, use jacks 20 and 21

and a Looper or MIDI Switcher (e.g. ENGL Z-11). Use two stereo ¼" cords to connect the ENGL

MIDI Switcher Z-11 (optional). You can then preset the four switching functions Clean/Lead, Gain

Lo/Hi, V.L.S. and Reverb via the Switcher, store your custom switching setups as different MIDI

programs and activate the presets via a MIDI board (e.g. ENGL Z-12).

22 F.X. Loop Send: Signal output for the Effects loop. Connect this output to a signal processor’s

input/return jack via a shielded cable with 1/4" plugs.

23 F.X. Loop Return: Signal input for the Effects loop. Connect this input to a signal processor’s

output/send jack via a shielded cable with 1/4" plugs.

24 Balance: FX mix control for the Effects loop: Rotate the knob to the "DRY" position for the pure

amp signal, i.e. no effect on the signal. Turn clockwise to blend in an effect connected to the loop

to the dry signal (parallel/passive). At the "EFFECT" position, only the wet signal, i.e. the signal

sent from the FX device is fed to the power amp (serial/passive).

NOTE: If no effects processor is connected to this loop, leave this control in the "DRY" position!

25, 26 Poweramp Output 8 ohms parallel: Parallel 8-ohm speaker outs, connected

internally in parallel. Connect an 8-ohm cabinet or, in the case of the Combo E330, its internal

speaker here. Alternatively, two 16-ohm cabinets can also be connected to these two outputs.

27 Poweramp Output 16 ohms serial: 16-ohm speaker out, connected internally in series

with Jack 28. Connect a 16-ohm cabinet here. Two 8-ohm speakers are connected to Jacks 27 and

28, for example a combination of the internal 8-ohm speaker of the Combo E330 and an external

8-ohm cabinet, e.g. the ENGL models E112 or E412.

CAUTION: If you intend to use a 16-ohm cabinet only, make absolutely certain you

connect it to Jack 27. Jack 28 is only enabled when a speaker is connected to jack 27.

28 Poweramp Output 16 ohms serial: 16 ohms serial. This is an auxiliary output connected

in series with Jack 27. This jack is designed for one application for only—when you are driving a

combination of two 8-ohm cabinets/speakers. This output may only be used when an 8-ohm

speaker is connected to Jack 27. (See the example for Item 27)

NOTE: Never operate the amplifier without a sufficient load, otherwise you may damage

or destroy the power amp! Ensure your cabinet’s specifications match the respective

output’s specs.

Possible speaker combinations:

1 x 8 ohms or 2 x 16 ohms (Jacks 25 and 26) or

1 x 16 ohms (Jack 27!) or 2 x 8 ohms (Jacks 27 and 28).

29 Line Out Ground: This switch assigns Pin 1 of the XLR socket to ground (position "Ground to

Pin 1"). You'll find this option is handy when you want to shield the circuit you have routed to a

mixing console or recording device. In order to come up with an unbalanced signal (e.g. for

feeding the signal to a computer for HD recording purposes), you'll need a cord equipped with an

XLR connector on one end and an RCA connector or ¼" plug on the other. Pin 2 is used to carry

the signal and Pin 1 as the ground (set the switch to the position "Ground to Pin 1"). With this

application—an unbalanced circuit—you may encounter a ground loop caused by the respective

grounds of the two devices, which will generate audible hum.

NOTE: Pin 1 of the balanced line may only be connected to ground on one end

(either at the amp or mixer / recording device), otherwise it may cause a ground loop,

which in turn generates undesirable hum!

30 Level: Signal level control for the frequency-corrected line output; it is used to match

the amp’s signal level at the Line output to the mixing console or recorder’s input.

31 Overload: This LED denotes the Line output is overloading; in this case,

reduce the signal’s level via the Level control.

32 Line Out Frequency Compensated

The frequency-corrected, balanced Line output jack (XLR; Pin 2 and 3 signal, Pin 1 = Ground or

not connected, depending on the setting of switch 29). This signal can be routed directly to a

mixing console or a recording unit. The line out is located post poweramp in the signal chain, so

ensure the poweramp is activated and a load is connected to one of the output jacks.A

A TIP from the Designer: The Line Out’s output level is influenced by the following factors: By the

input level (Gain), the Volume control settings for the various channels, to some degree by voicing

control settings, and by the Master volume level. First dial in the desired sound combination at the

front panel. Then adjust levels at FX devices or signal processors (if connected). Now use the Level

control to adjust the Line level. The Line output is not overloaded until the Overload LED

illuminates brightly and continuously. You can push the level up to this point to match a mixing

console or recorder’s input level requirement. Use the respective device’s input sensitivity or gain

control to fine-tune level adjustments.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Engl Screamer 50 Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info