Bedienungsanleitung Entone URC 4 (Seite 13 von 26) (Englisch)

492809

Zoom out

Zoom in

Vorherige Seite

1/26

Nächste Seite

URC 4 User’s Guide



v2.5 for URC 4

To Program a TV or AUX device

1. Locate the device code for your desired device in the device code table provided in the Appendix. If you

could not find the device code for your device or it does not work after trying the listed device codes for

your device brand, then you can go to the next section to try the auto search procedures.

2. Turn on your device and with media inserted (if applicable).

3. On the remote control, press a device mode key for 5 seconds (i.e., “TV” or “AUX”). The device mode

key will light up.

NOTE: Use the “AUX” mode key to program control of VCR, DVD player, cable box, satellite set-top-

box and audio device.

4. Enter the four-digit device code for you device. If you perform this procedure correctly, the selected

device mode key backlight will blink twice.

NOTE: If you enter an invalid device code, the selected device mode key will fast blink 7 times. Device

program mode will be terminated.

5. Aim the remote control at your device and press the “POWER” once. The device should be turned off.

If it does not respond, repeat the above steps.

NOTE: In the programming mode if no key is received within 30s, the device mode key backlight will

blink rapidly for 7 times to indicate an error and then extinguish, and the programming mode will end.

Toggle Power Key Punch-through Functionality

By default, if the remote control is in STB mode, the URC Power button switches STB off ONLY. To control

the URC Power button functionality to switch off either both the TV and/or STB, do the following:

1. Press and hold the “STB mode key for 5s. The “STB” device mode key backlight will light up.

2. Press “POWER” key once.

3. Either do the following:

a. Press 1 to control both the STB and TV, OR

b. Press 0 to control the STB ONLY

NOTE: In the programming mode if no key is received within 30s, the device mode key backlight will blink

rapidly for 7 times to indicate an error and then extinguish, and the programming mode will end.

Toggle Volume Key Punch-through Functionality

By default, Vol +/- and MUTE keys are sent to STB only when URC is in STB mode.

Punch-through function for those keys is enabled at the same time when programming the device code for

TV or AUX. That is:

1. If user program device code for a TV device, the punch through function will be configured for TV at the

same time.

2. If user program device code for an AUX device, the punch through function will be configured for AUX

at the same time.

To disable the Punch-through function for those keys, do the following:

1. Press and Hold STB for 5 seconds, then STB led will switch on.

2. Press STB key once again, then both STB and AUX led will switch on.

3. Press 0

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Entone URC 4 Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info