Bedienungsanleitung Entrematic Sesam 600 (Seite 19 von 56) (Deutsch, Englisch, Französisch, Schwedisch)

680521

Zoom out

Zoom in

Vorherige Seite

1/56

Nächste Seite

EasyLift 500 / Sesam 600 MA120527=>2012-05 19 / 56

ATTENTION: No protection is provided by the load

switch-off whilst the door operator is being taught

in.

Note: Teaching in is only possible during initial installation or

after resetting the door operator. Do not press any button

during the teach-in procedure.

Preparation: Connect the door to the door operator.

Teach in travel distance and force values

• Press and hold the CANC button (12).

• Press and hold the TEST button (13) until LED1 (red) and

LED2 (green) flash alternately.

• When both LED‘s no longer flash, release both

buttons (12+13).

• Wait until both LED‘s (1+2) flash in sync.

• Press and hold the TEST button (13) until the door is

almost closed.

• Close the door completely in jog mode (tap the TEST

button to move the door) (door position closed), LED 1

(red) lights *.

• Teach in door position closed by pressing the CANC button

(12), LED 1 (red) goes out and LED 2 (green) lights up.

• Press and hold the TEST button (13) until the door is

almost fully open.

• Open the door fully in jog mode (tap the TEST button to

move the door).

• Teach in door position open by pressing the CANC button

(12), LED 1 (red) lights up and LED 2 (green) goes out.

• Teach in force values by pressing the TEST button (13),

the operator closes and opens the door, LED 1 (red) LED 2

(green) flash alternately. When the force values have been

taught in, only LED 1 (red) flashes.

The door operator is taught in.

* If the operator has moved too far when setting “door position

closed” (chain hanging out of the rail runner)

• Press the CANC button (12).

• Open the door half way with the TEST button (13).

• Pull out the mains plug, wait about 5 seconds and plug it

back in.

• Teach in travel distance and force values again.

Teach in remote transmitter:

• Press the PROG button (11), LED 2 (green) lights up.

• Press the desired button on the remote transmitter, LED 2

goes out.

• Press the desired button on the remote transmitter, LED 2

flashes slowly and goes out.

The remote transmitter is taught in.

Deleting (all) remote transmitter(s):

• Press and hold the PROG button (11) until LED 2 (green)

flashes rapidly.

• Release the PROG button, all saved remote transmitters

are deleted.

CAUTION: Mishandling the product can result in

injuries or material damage. Follow the basic safety

rules:

When opening or closing the door, do not block the interior or

exterior swivel ranges. Keep children away.

The door movements can be activated or stopped using the

remote transmitter provided or via switching elements such

as the wall keypad, which can be connected if desired.

Optional external features (such as the EMERGENCY

STOP) can also be connected to the door operator.

The operator must be connected to a door before

it is used. If it is not, incorrect load values will be

taught in to the electronic system. This can cause

malfunctions.

ATTENTION: There is no longer any protection by

switching off the load after the reset. Teach the

door operator in again before re-commissioning. For this

carry out Teaching in the Door Operator (Chapter 15) .

• Press and hold the CANC button (12).

• Press and hold the TEST button (13) until LED1 (red) and

LED2 (green) flash alternately.

• When both LED‘s no longer flash, release both

buttons (12+13).

• Wait until both LED‘s (1+2) flash in sync, all values are now

deleted.

Connect the light barrier as illustrated (remove jumper

between connection 6+7)

15 Teaching in the Door Operator

16 Teaching in/Deleting a Remote

Transmitter

17 Operation

18 Reset

19 Connecting the Light Barrier

5 = GND

6 = Signal

7 = 24V

STORING A RADIO TRANSMITTER:

- Press the PROG(11) button; LED 2 (green) and the red

LED on the radio receiver card come on

- Press the desired button on the transmitter; LED 2 (green)

and/or the red LED on the radio receiver go out and then

come on again.

- Press the desired button on the transmitter again; LED 2

(green) and/or the red LED on the radio receiver flash on

and off. The transmitter has now been stored.

DELETING ALL RADIO TRANSMITTERS:

- Hold down the PROG(11) button until the red LED on the

radio receiver flashes on and off

- Release the PROG button and press it again until the red

LED on the radio receiver rapidly flashes on and off; all the

stored radio transmitters have been deleted

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Entrematic Sesam 600 Seite 19

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info