Bedienungsanleitung Entrematic Superior plus 42 TOF (Seite 22 von 24) (Alle Sprachen)

680496

Zoom out

Zoom in

Vorherige Seite

1/24

Nächste Seite

11.

Assembly of the balancing package is the same for

Torsion Front and Torsion Rear concept. Start to assemble

the right half of the balancing package. (Spring is marked

red)

First pull the spring out from the shaft (shaft inside the

spring approx 50 mm, to be able to turn the spring brake

device on to the spring). (1)

The spring brake device should catch on to the spring

hook.

(2)

Push the shaft through the spring brake device until a stop

ring on the shaft meets the bottom of the spring brake

device. (3)

Push the R marked (for right side) drum on the shaft (4)

until the pre-assembled thread-hook locks the drum on the

outside. (5).

Slide the centre-bearing ring on to the shaft. (6)

Slide the shaft coupling on. (7)

Now assemble the left half of the balancing package. Left

spring is marked black.

12. TOF

14.

Assemble the mid-rollers as shown. Oil the roller shaft. (1)

Place two supports, approximately 350mm high on the

floor

on which you will place the bottom section. (2)

Position the bottom section on the supports and in the

wall-tracks. (3)

Insert the mid-rollers to the right and left hand sides (this

will hold the bottom section in position). (4) Fix the mid-

roller with 1 x panelscrew.

10.

Fix clips to both ceiling tracks to secure the spacer bar,

using panel screws. (1)

Support

for ceiling tracks when B > 2250 mm, 1 addi-

tional

hanger to each ceiling track. (2)

Cut any excess from the support bars left protruding from

below the spacer bar on both sides of the spacer bar and

grind the sharp edges (corners) off on all hangers (3).

Clip the side sealing on, start from bottom (4).

Adjustments

Measure from corner to corner. This measurement should

be equal and if not reposition the tracks to ensure they are

parallel and square to the opening. (5)

Adjust the tracks to the door section to ensure the same

distance from door to ceiling track, both right and left

side. Adjust by loosing the distance beam clips, for adjust-

ment of the distance beam side-ways. Put the bracing on

both hangers by drilling 4,5 mm holes in the spacer beam

and fix by track screw (3).

Tighten all screws and nuts at the ceiling hangers.

Ensure both ceiling tracks are level (1), by adjusting the

position

of the spacer bar (2). Fix the curves (no left or

right version). Start to fix and adjust the ceiling-joint (3),

then the joint to the wall-track (4). Use the special round

flat-headed coach-bolt M-6 and collar nuts. Tighten the

lintel / ceiling-track screws (5, 6). Fix the upper ceiling

wall-track part to the wall by the 50 mm screws right and

left track (7). (The lintel gives the distance between the

upper ceiling wall-track parts)

13.

The bottom rubber weather seal has an inbuilt ventila-

tion function. By separating the rubber sealing from the

perforated plastic profile, the ventilator can be closed. Just

turn the rubber part 180° from its original position and re-

assemble the sealing. (1,3)

Apply the bottom door section rubber seal to the bottom

section,

as shown (2,4)

Fix the bottom rubber seal bracket to the centre of the

panel

using 2 panel screws (5).

Sections are packed in the following order: bottom sec-

tion, first mid section, second mid section etc, and top sec-

tion (65 mm shorter than the other sections).

12. TOR

Install the mid ceiling hanger and centre bearing bracket

using M-8 coach bolts. (1)

Install

the spring holding brackets using track screws.(2)

Put the right half of the spring balancing package up by

letting the shaft rest in the centre-bearing bracket. Position

the centre-bearing ring in the bracket. (3)

Hook the spring bracket into the spring holding bracket.

(4)

Fix the spring bracket to the spring holding bracket by one

panel screw. (5)

Put the left half of spring balancing package up and

tighten (temporarily) on screw at the shaft coupling. (6)

Remove the lock pin right and left springs to activate the

spring break device (7).

Install the spring holding brackets and fix to the wall. (1)

Put the right half of spring balancing package up, by

letting

the spring shaft rest in the centre-bearing bracket.

(2)

Hook the spring bracket into the spring holding bracket.

(3)

Fix the spring bracket to the spring holding bracket by 1

panel screw. (4)

Remove the lock pin left and right springs (5). The spring

break device is now activated.

Put the bearing ring on to the centre-bearing bracket. (6)

Put the left half of spring balancing package and tighten

(temporarily) one screw at the shaft coupling. (7)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Entrematic Superior plus 42 TOF Seite 22

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info