Bedienungsanleitung Epson EB-685Wi (Seite 230 von 253) (Englisch)

675176

230

Zoom out

Zoom in

Vorherige Seite

1/253

Nächste Seite

Solving Interactive Features Problems

230

• Make sure the projector is not too close to the projection surface.

• Move the projector or turn off the interfering device, such as a light source

that is emitting infrared rays.

Solutions When You Cannot Operate a Computer

from the Projected Screen

If you cannot operate a computer from the projected screen, try the following

solutions:

• Make sure the USB Type B option on the Extended menu is set to Easy

Interactive Function or USB Display/Easy Interactive Function.

• Make sure you perform pen calibration when using the interactive pen for

the first time so that the projector recognizes the position of the pen

correctly.

• Press the [Pen Mode] button on the remote control to select PC Interactive

as the Pen Mode setting. You can also select the Pen Mode setting from the

projector's Extended menu.

s Extended > Easy Interactive Function > Pen Mode

• Make sure the USB cable is securely connected. Disconnect the USB cable,

and then reconnect it.

• When projecting an image using two projectors installed side by side, you

need to select the Multi-Projection setting to use the interactive features.

You also need to install Easy Interactive Driver Ver. 4.0 from the Epson

Projector Software for Easy Interactive Function CD-ROM on the computer

that you want to operate from the projected screen.

s Extended > Easy Interactive Function > Advanced > Multi-Projection

• When projecting an image with only one of the two projectors installed side

by side, you may not be able to operate a computer from the projected

screen. Select the icon on the Home screen, and then set Use this

single projector to On.

gg Related Links

• "Pen Calibration" p.77

• "Projector Setup Settings - Extended Menu" p.178

Solutions When the Interactive Pen Position Is Not

Accurate

If the pen position is not the same as the mouse pointer, try the following

solutions:

• Make sure you perform pen calibration when using the interactive pen for

the first time so that the projector recognizes the position of the pen

correctly. If the cursor location and pen position do not match after auto

calibration, you can calibrate manually.

• Make sure the cable cover is in place to keep cables from blocking the

signal.

• Try adjusting the pen operation area.

• If you use the [E-Zoom] + button on the remote control to enlarge the

image, the pen position is not accurate. When you return the image to the

original size, the position should be correct.

• If you set Pen Mode to PC Interactive in the projector's Extended menu,

set Auto Adjust Pen Area to Off, and then select Manual Adj. Pen Area.

s Extended > Easy Interactive Function > General > Advanced > Auto

Adjust Pen Area

s Extended > Easy Interactive Function > General > Advanced >

Manual Adj. Pen Area

• Try changing the computer's resolution to 1280 × 800.

gg Related Links

• "Pen Calibration" p.77

• "Projector Setup Settings - Extended Menu" p.178

• "Adjusting the Pen Operation Area" p.93

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Epson EB-685Wi Seite 230

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Epson EB-685Wi

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info