Bedienungsanleitung Epson EB-725Wi (Seite 31 von 312) (Englisch)

737380

Zoom out

Zoom in

Vorherige Seite

1/312

Nächste Seite

Projector Placement

Attention

The interactive features are operated using infrared communication. Note the

following points when installing the projector.

• Do not install the projector tilted at an angle of 3˚ or more. The interactive

features may not operate correctly.

• Make sure there is no strong light or sunlight shining on the interactive pen

receiver, the projection screen, the projector itself, or the rear of the projector.

• Do not install the projector where it could be subjected to direct sunlight

through a window. This could cause the interactive features to malfunction.

• Install the projector so that the interactive pen receiver is not too close to

fluorescent lights. If the surrounding area is too bright, the interactive features

may not operate correctly.

• If there is any dust stuck to the interactive pen receiver, it could interfere with

infrared communication and the interactive features may not operate correctly.

Clean the receiver if it is dirty.

• Do not put paint or any stickers on the cover of the interactive pen receiver.

• When using the interactive features, do not use an infrared remote control or

microphone in the same room. The interactive pen could malfunction.

• Do not use devices that generate powerful noise, such as rotary devices or

transformers, near the projector, as the interactive features may not operate

correctly.

• We recommend using a smooth, board type screen without any

unevenness. If the projection screen is uneven, there may be

distortions in the projected image.

• Distortions may occur in the projected image depending on the

material of the screen and the installation method.

• When using the interactive features, install the projector so that the

projected screen is a rectangle without any distortion.

• When using the interactive features in the same room as multiple

projectors, interactive pen operations may become unstable. In this

case, connect the optional remote control cable set to the projectors,

and change Sync of Projectors to Wired in the projector's

Pen/Touch menu.

s Pen/Touch > Installation of Projectors > Sync of Projectors

gg Related Links

• "Settings when Using the Touch Unit" p.31

• "Connecting a Computer for Use with PC Interactive Features" p.35

Settings when Using the Touch Unit

When using the Touch Unit, install the projector using one of the following

methods. The Touch Unit cannot be used if another installation method is

used.

• Mount the projector on a wall or suspend it from a ceiling and project

images from in front of the screen (the setting plate or a commercially

available ceiling mount is required).

• Install vertically on a desk and project from the front of the desk (a

commercially available table mount is required).

See your projector's Installation Guide for the Touch Unit installation

methods and angle adjustment methods.

gg Related Links

• "Safety Instructions for Interactive Touch Operations" p.99

• "Using Interactive Touch Operations with Your Finger" p.98

• "Getting the Latest Version of the Documents" p.10

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Epson EB-725Wi Seite 31

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Epson EB-725Wi

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info