Bedienungsanleitung Epson EB-G5600 (Seite 97 von 180) (Englisch)

500243

Zoom out

Zoom in

Vorherige Seite

1/180

Nächste Seite

Other problems

No sound can be heard or the sound is faint (EB-G5950/G5900/G5650W/G5600 only)

Check Remedy

Is the audio source connected correctly? Disconnect the cable from the audio input port, and then reconnect the cable.

Is the volume adjusted to the minimum setting? Adjust the volume so that sound can be heard. s Quick Start Guide

Is A/V Mute active? Press the [A/V Mute] button on the remote control to cancel A/V Mute. s p.38

Is the audio cable's specification "No resistance"? When using a commercially available audio cable, make sure it is labeled "No resistance".

Is it connected with an HDMI cable? If no audio is output when connecting via an HDMI cable, set the connected equipment to PCM output.

Is the correct setting for the HDMI Audio Input selected?

Only when the input source is HDMI

Check the HDMI Audio Input from the configuration menu. s Settings Menu - Audio Input - HDMI Audio Input

p.59

Is the correct setting for the LAN Audio Input selected?

Only when the input source is LAN

If the audio from a computer that is connected through a network is not output, check the setting of the LAN Audio

Input on the configuration menu. s Settings Menu - Audio Input - LAN Audio Input p.59

The remote control does not work

Check Remedy

Is the remote control light-emitting area pointing towards the

remote receiver on the projector when it is operated?

Point the remote control towards the Remote Receiver. s p.19

Is the remote control too far from the projector? The operating range for the remote control is about 15 m. s p.19

Is direct sunlight or strong light from fluorescent lamps shining onto

the Remote Receiver?

Set the projector up in a location where strong light does not shine onto the remote receiver. Or set the remote receiver to

Off from Remote Receiver in the configuration menu. s Settings Menu - Remote Receiver p.59

Is the correct setting for the remote receiver selected? Check the Remote Receiver from the configuration menu. s Settings Menu - Remote Receiver p.59

Are the batteries dead or have the batteries been inserted correctly? Make sure the Batteries are inserted correctly or replace the batteries with new ones if necessary. s p.18

Are the remote control ID and the projector ID matched? Make sure the ID for the projector you want to operate and the ID for the remote control match. To operate all projectors

by remote control regardless of the ID setting, set the ID switch on the side of the remote control to Off. s p.42

Does Remote Control Type match the remote control that you are

using?

Check the Remote Control Type on the configuration menu. s Extended Menu - Operation - Remote Control Type

p.61

Is the optional remote control cable connected to the remote control

or to the projector's remote port?

When the remote control cable is connected, the remote control light-emitting area or the projector's remote receiver are

disabled. When not using the remote control cable set, disconnect it from the remote control and the remote port.

Problem Solving

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Epson EB-G5600 Seite 97

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Epson EB-G5600

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info