Bedienungsanleitung Epson EB-G7500U (Seite 56 von 255) (Englisch)

675247

Zoom out

Zoom in

Vorherige Seite

1/255

Nächste Seite

Before turning on the projector, connect your computer or video equipment

to the projector.

s "Connecting Equipment" p.46

Connect the projector to an electrical outlet with the power cord.

The projector's power indicator turns blue (it is in standby mode).

This indicates that the projector is receiving power, but is not yet

turned on.

Press the [ ] button on the control panel or remote control to

turn on the projector.

The confirmation buzzer beeps and the status indicator flashes blue

as the projector warms up. Once the projector is warmed up, the

status indicator stops flashing and turns blue.

If the image is not projected, try the following.

• Turn on the connected computer or video equipment.

• When using a laptop computer, change the screen output of the

computer.

• Insert media such as a DVD and play it back.

• Press the [Search] button on the control panel or the remote control to

detect the input source.

• Press the button for the input source that you want to project by using

the remote control.

• If the Home screen is displayed, select the input source that you want

to project.

Warning

• Do not look into the projector's lens during projection. Doing so may

damage your eyes. Be especially careful if children are present.

• During projection, do not block the light from the projector with a book and

so on. If the light from the projector is blocked for a long time, the area on

which the light shines becomes hot which could cause it to melt, burn, or

start a fire. Also, the lens may get hot due to the reflected light which could

cause the projector to malfunction. To stop projection, use the A/V Mute

function or turn off the projector.

• A mercury lamp with high internal pressure is used as the projector's light

source. If the lamp is subjected to vibrations, shocks, or if it is used for an

overly extended length of time, the lamp may explode with a loud noise or it

may not turn on. If the lamp explodes, gases may escape and small fragments

of glass may be scattered which could cause an injury. Be sure to observe the

instructions below.

- Do not disassemble or damage the lamp or subject it to any impact.

- Do not bring your face close to the projector while it is in use.

- Particular care should be taken when you must clean or replace the lamps

by yourself, as small pieces of glass may injure you or enter your eyes or

mouth. (When you open the lamp cover, small shards of glass could fall

out.)

If the lamp explodes, ventilate the area immediately, and contact a doctor if

any fragments of broken glass are inhaled or get into the eyes or mouth. In

addition, consult your local regulations regarding proper disposal and do not

place in the trash.

Turning On the Projector

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Epson EB-G7500U Seite 56

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Epson EB-G7500U

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info