617828
160
Zoom out
Zoom in
Vorherige Seite
1/166
Nächste Seite
160
List of Safety Symbols (corresponding to IEC60950-1 A2)
The following table lists the meaning of the safety symbols labeled on the
No. Symbol mark Approved Description
equipment.
standards
I
The same as No.8.
No. Symbol mark Approved Description
standards
J
IEC60417 Battery, general
A
IEC60417 "ON" (power)
No.5001B On battery powered equipment. To
No.5007 To indicate connection to the mains.
identify a device for instance a cover
for the battery compartment, or the
connector terminals.
B
IEC60417 "OFF" (power)
K
IEC60417 Positioning of cell
No.5008 To indicate disconnection from the
No.5002 To identify the battery holder itself
mains.
and to identify the positioning of the
cell(s) inside the battery holder.
C
IEC60417 Stand-by
L
The same as No.11.
No.5009 To identify the switch or switch
position by means of which part of the
equipment is switched on in order to
M
IEC60417 Protective earth
bring it into the stand-by condition.
No.5019 To identify any terminal which is
D
ISO7000 Caution
intended for connection to an external
No.0434B, To identify general caution when
conductor for protection against
using the product.
IEC3864-B3.1
electric shock in case of a fault, or the
terminal of a protective earth
E
IEC60417 Caution, hot surface
electrode.
No.5041 To indicate that the marked item can
N
IEC60417 Earth
be hot and should not be touched
No.5017 To identify an earth (ground) terminal
without taking care.
in cases where neither the symbol
F
IEC60417 Caution, risk of electric shock
No.13 is explicitly required.
No.6042 To identify equipment that has risk of
O
IEC60417 Alternating current
electric shock.
ISO3864-B3.6
No.5032 To indicate on the rating plate that the
equipment is suitable for alternating
G
IEC60417 For indoor use only
current only; to identify relevant
No.5957 To identify electrical equipment
terminals.
designed primarily for indoor use.
P
IEC60417 Direct current
H
IEC60417 Polarity of d.c. power connector
No.5031 To indicate on the rating plate that the
equipment is suitable for direct
No.5926 To identify the positive and negative
current only; to identify relevant
connections (the polarity) on a piece
terminals.
of equipment to which a d.c. power
supply may be connected.
160

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Epson EB-X130 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Epson EB-X130

Epson EB-X130 Bedienungsanleitung - Deutsch - 169 seiten

Epson EB-X130 Bedienungsanleitung - Holländisch - 169 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info