214277
38
Zoom out
Zoom in
Vorherige Seite
1/121
Nächste Seite
37
Turning the Projector On
User’s Guide
If more than one external device is connected to the
projector, use the remote control or projector control
panel buttons to select the image source to be
projected while referring to the following table.
The input source can also be searched for and
projected automatically each time the [Source
Search] button is pressed.
*1 Displays the selected source as the "Computer Input" - "Signal" in the
configuration menu.
*2 Only changes when using the EMP-745/737.
s
EasyMP Operation Guide
and the
EasyMP Network Setup Guide
for details on using EasyMP.
Source
Remote control
button selected
Display at top-right of screen
Computer/
Component Video
Computer
Computer (Auto)
*1
Computer
*1
Component Video
*1
S-Video S-Video S-Video
Video Video Video
EasyMP
*2
EasyMP
EasyMP
4
ProjectorRemote control
TIP
TIP
If only one signal source has been connected, the signals from that
source will be projected without the need to press any of the buttons
on the remote control or the projector's control panel.
If using an EMP-745/737, EasyMP is detected as a source by
pressing the [Source Search] button only when the CardPlayer is
running with an inserted memory card or connected USB
equipment, or when a LAN card is inserted. When EasyMP is not
displayed by the [Source Search] button, press the [EasyMP] button
on the remote control to switch the projected image to EasyMP.
If the "No Signal." message does not disappear, check the
connections again.
If a laptop computer or a computer with an LCD screen has been
connected to the projector, the images may not be projected straight
away. After starting projection, check that the computer has been set
up to output signals externally.
The following table shows examples of how to toggle output settings.
For details, refer to the section of the documentation provided with
your computer under a heading such as "External output",
"Connecting an external monitor" or similar.
If the same still picture is projected for a long period of time, the
projected image may become burned into the screen. You should
avoid leaving the same image displayed for long periods.
NEC Panasonic To shi b a IBM Sony Fujitsu Macintosh
[Fn]+[F3] [Fn]+[F3] [Fn]+[F5] [Fn]+[F7] [Fn]+[F7] [Fn]+[F10]
Set mirror setting or
display detection.
38

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Epson emp 740 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info