214277
90
Zoom out
Zoom in
Vorherige Seite
1/121
Nächste Seite
89
Problems Solving
User’s Guide
The projector cannot be monitored and controlled using the EMP Monitor function
When Network Screen is running, the current image stays projected and connection from another computer is not possible
Check Remedy
Is the wireless or wired LAN card inserted? Check that the wireless or wired LAN card is correctly inserted into the card slot of the projector.
"Inserting and Removing Cards" sp.17
Is the network cable connected correctly? Check that the network cable is connected correctly. If it is not connected or is connected
incorrectly, reconnect it.
Are the settings for connecting to a network
correct ?
Check the network settings for the projector.
s"Connecting in Access Point Mode or Wired LAN Mode" in the EasyMP Network Setup Guide
Has EMP Monitor function been correctly
installed to the computer?
Uninstall EMP Monitor and then re-install it.
s"If You would like to Uninstall the EasyMP Software" and "Installing EasyMP Software" in the
EasyMP Network Setup Guide
Have all projectors that are to be monitored
and controlled been registered in the
projector list?
Register the projector in the projector list. sEMP Monitor Operation Guide
Has "Standby Mode" been set to "Network
ON"?
If using the EMP Monitor function while the projector is in standby mode, change the "Standby
Mode" menu setting to "Network ON". "Extended" - "Standby Mode" sp.66
Is power being supplied to the projector? Check if the power supply to the location where the projector is set up has been interrupted, or if the
circuit breaker for the electrical outlet that the projector is connected to has been tripped.
Check Remedy
Has the person making the presentation left
the meeting room without closing the
connection?
If you try to connect to a projector from a computer while Network Screen is running and the
projector is already connected to another computer, the connection to the first computer will be
terminated and the projector will then connect to the next computer.
If no projector keyword has been set in the projector or the keyword is known, it is possible to
terminate the current connection and connect to the projector by establishing a new connection from
the computer.
If a projector keyword has been set in the projector and the projector keyword is unknown, terminate
the connection from the projector and then reconnect. To terminate the connection from the
projector, press the [Esc] button on the remote control, select the "Exit" button from the displayed
menu and then press the [Enter] button on the remote control. Connect from the desired computer
after terminating the connection.
s"Disconnecting from a Network Connection" in the EasyMP Network Setup Guide
When connected to a wired LAN
90

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Epson emp 740 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info