36096
50
Zoom out
Zoom in
Vorherige Seite
1/85
Nächste Seite
45
Problems Solving
High temperature error
(overheating)
The lamp will turn off automatically and projection will stop. Wait for about 5 minutes. After
about 5 minutes the projector will switch to standby mode, so check the following two points.
After checking, press the [Power] button to turn the power back on.
Check that the air filter and air exhaust vent are clear, and that the projector is not positioned
against a wall.
If the air filters are blocked, clean or replace them. sp.57, p.63
If this does not solve the problem and the projector continues to overheat or the indicators continue
to show a problem when the power is turned on, stop using the projector, disconnect the power cable
from the wall outlet, and contact your dealer or the nearest address provided in the "International
Warranty Conditions" section of the
Safety Instructions/World-Wide Warranty Terms
booklet.
Lamp problem
Lamp timer failure
Lamp cover is open
Check that the lamp is not cracked and that the air filter and air intake vent are clear.
Remove the lamp and check if it is cracked. sp.59
Clean the air filter and the air intake vent. sp.57
If it is not cracked Replace the lamp and turn on the power.
If error still occurs Replace it with a new lamp and turn on the power.
If error still occurs Stop using the projector, disconnect the power cable from the wall
outlet, and contact your dealer or the nearest address provided in the
"International Warranty Conditions" section of the Safety
Instructions/World-Wide Warranty Terms booklet.
If it is cracked Contact your dealer or the nearest address provided in the "International
Warranty Conditions" section of the Safety Instructions/World-Wide Warranty
Terms booklet.
(You cannot continue projecting until the lamp is replaced).
Check that the lamp cover and the lamp are securely installed. sp.59
If the lamp cover or the lamp is not securely installed, the lamp does not switch on.
When using above an altitude of about 1500m, make sure you set the "High Altitude
Mode" to "On". sp.38
: lit : flashing : off
Status Cause Remedy or Status
Red
Red
Power
Red
Red
Power
50

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Epson EMP-82 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Epson EMP-82

Epson EMP-82 Bedienungsanleitung - Deutsch - 87 seiten

Epson EMP-82 Bedienungsanleitung - Holländisch - 81 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info