Bedienungsanleitung Epson EMP-TW20 (Seite 37 von 56) (Englisch)

6486

Zoom out

Zoom in

Vorherige Seite

1/56

Nächste Seite

Troubleshooting

Problem Solving

The message "Not Supported." is displayed

The message "No Signal." is displayed

Are the image signal format

settings correct?

If the signal source is connected to the [InputA] port

Use the "Input Signal" menu command to set the signal format that

matches the signal that is being projected from the connected

equipment.

"Setting" - "Input Signal" - "Input A" p.30

You can also press on the remote control to select the format.

p.15

If the VCR or DVD equipment is connected using an RGB SCART

adapter

Press to set the signal format to “RGB-Video”. p.15

When still no images appear and the DVD equipment is connected,

change the setting at the DVD equipment to RGB output.

Have the configuration menu

settings been made correctly?

Try resetting all of the current settings. p.31

Were the projector and

computer connected while their

power was already turned on?

If the connection is made while the power is already turned on, the

function (Fn) key that switches the computer's video signal to

external output may not work. Turn the power for the computer that

is connected to the projector off and then back on again.

Is the computer display output

set to only the computer's

accessory screen?

The image signals need to be output externally. Change the output

setting to an external destination only or to an external destination as

well as the computer's own monitor.

Computer documentation, under a title such as "External output"

or "Connecting an external monitor"

Are the image signal format

settings correct?

If a composite video or S-Video signal is being input

If projection does not occur when the "Video Signal" menu

command is set to "Auto", select the signal format that matches the

signal source. "Setting" - "Input Signal" - "Video Signal" p.30

If the signal source is connected to the [InputA] port

Use the "Input Signal" menu command to set the signal format that

matches the signal that is being projected from the connected

equipment. "Setting" - "Input Signal" - "Input A" p.30

You can also press on the remote control to select the format.

p.15

Does the mode match the

frequency and resolution of

the image signals?

Use the "Resolution" menu command to check the signals being

input, and check the "List of compatible signals" to make sure that

the signals are compatible.

"Info" - "Resolution" p.25

"List of Supported Monitor Displays" p.45

Are the cables connected

correctly?

Check that all of the cables required for projection are securely

connected. p.12

Has the correct video input

port been selected?

Press , , or on the remote control or on

the projector's control panel to change the image source. p.15

Is the power for the connected

equipment turned on?

Turn the power on for the devices.

When a computer is

connected

When a computer is

connected

Only when projecting

computer images

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Epson EMP-TW20 Seite 37

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Epson EMP-TW20

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info