Bedienungsanleitung Epson emp tw620 (Seite 41 von 60) (Englisch)

214613

Zoom out

Zoom in

Vorherige Seite

1/60

Nächste Seite

Problem Solving

Troubleshooting

■ Interference or distortion appear in images

■ Image is truncated (large) or small

Has condensation formed on the

lens?

If the projector is suddenly taken from a cold environment to a

warm environment or if sudden ambient temperature changes

occur, condensation may form on the surface of the lens, and this

may cause the images to appear fuzzy. Set the projector up in the

room approximately one hour before it is to be used. If

condensation forms on the lens, turn the power off and wait for the

condensation to disappear.

Are the image signal format

settings correct?

If a composite video or S-Video is being input

If projection does not occur when the "Video Signal" menu

command is set to "Auto", select the signal format that matches the

signal source.

"Settings" - "Input Signal" - "Video Signal" p.33

If the signal source is connected to the [InputA] port

If projection does not occur when the "InputA" in the "Input

Signal" menu command is set to "Auto", set the signal format that

matches the signal that is being projected from the connected

equipment. "Settings" - "Input Signal" - "Input A" p.33

You can also press on the remote control to select the

format. p.15

Are the cables connected

correctly?

Check that all of the cables required for projection are securely

connected. p.12

Is an extension cable being

used?

If an extension cable is used, interference may increase. Try

connecting a signal amplifier.

Have the "Sync.

" and

"Tracking

" settings been

adjusted correctly?

The projector has an automatic adjustment function that causes the

optimum images to be projected. However, for some types of

signal, the correct adjustments may not be obtained even after

automatic adjustment is carried out. In such cases, use the

"Tracking" and "Sync." menu commands to make the adjustments.

"Image" - "Tracking", "Sync." p.29

Has the correct resolution been

selected?

Set the computer so that the signals that are output are compatible

with this projector.

"List of Supported Monitor Displays" p.47

Computer documentation

Has the correct aspect

been

selected?

Press to select the aspect that corresponds to the input

signal. p.18

If images with subtitles are being projected using "Zoom", use the

"Zoom Caption" menu command to adjust the images. p.29

Has the "Position" setting been

adjusted correctly?

Use the "Position" the menu command to make the adjustment.

"Image" - "Position" p.30

Has the computer been set for

dual display?

If dual display has been activated in the Display Properties of the

computer's Control Panel, the projector will only project about half

of the image on the computer screen. To display the whole of the

image on the computer screen, turn off the dual display setting.

Computer video driver documentation

Computer and RGB

video signals only

Only when projecting

computer images

Only when projecting

computer images

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Epson emp tw620 Seite 41

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Epson emp tw620

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info