Bedienungsanleitung Epson SC-F2100 - SURECOLOR (Seite 112 von 143) (Englisch)

675424

112

Zoom out

Zoom in

Vorherige Seite

1/143

Nächste Seite

Platen Height Error is displayed while

printing

Are you printing a job over the entire print

area that requires a large amount of ink?

When printing a job that requires a large amount of

ink, the printed surface may expand due to the

amount of ink and the height position sensor may be

triggered during printing even if the T-shirt has been

loaded correctly. If this happens, try placing the T-shirt

over the platen as shown in the following illustration.

If the sensor is triggered even if the T-shirt is loaded

using a frame as shown in the illustration above,

removing the frame may smooth out any creases or

slack in the printed surface and solve the problem.

Note that the following steps are necessary if you

remove the frame.

❏ Reduce the width of the White ink in the printer's

Garment Creator software or in the RIP software,

so that the white under-base print does not

extend outside the image.

❏ Be careful not to touch the T-shirt while printing

as it can easily move out of position.

Have you dried pre-treatment liquid

completely?

The print surface becomes wet and swells if the

pre-treatment liquid is not dried sufficiently before

printing, and it may trigger the height position sensor.

Check that the pre-treatment liquid is dry.

Areas not printed are stained with ink

Is the platen clean?

The platen's frame and the top plate may be stained.

Check the platen and clean it if necessary.

U “Clean the Platen without Grip Pad” on page 94

Even after cleaning the scale, a

cleaning message is displayed

Is there any dust or ink cleaner on the scale?

If dust or ink cleaner remain on the scale after wiping, a

cleaning message is displayed. Check that there is no

dust or ink cleaner remaining on the scale.

If this message appears on the LCD panel again,

contact your dealer or Epson Support.

The printer status and log are printed

over the edges of the paper

Are you printing with an M size (standard)

platen?

Depending on the paper size the print area may

extend beyond the edges of the paper if paper is

loaded on an optional platen. Load paper on the M

size (standard) platen, and then print.

U “Load the T-shirt (media)” on page 45

Printing is slow or stops half way

Is the head move direction set to

uni-directional?

Print Direction may be set to Uni-Direction (Low

Speed) in the Garment Creator software for the

printer. Try setting Print Direction to Bi-Direction

(High Speed) in the printer's Garment Creator

software.

When printing a job from the USB memory stick, Prt

Direction may be set to Uni-Directional on the

preview screen. Disable the Uni-Directional setting.

U “Printing from a USB Memory” on page 58

SC-F2100 Series User's Guide

Problem Solver

112

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Epson SC-F2100 - SURECOLOR Seite 112

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Epson SC-F2100 - SURECOLOR

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info