Bedienungsanleitung Epson Stylus Pro 11880C (Seite 162 von 182) (Englisch)

617755

162

Zoom out

Zoom in

Vorherige Seite

1/182

Nächste Seite

Problem Solver 162

User’s Guide

The print is not positioned

properly on the paper.

Have you specified the print area?

Check the print area in the settings of the application and printer.

Is the paper size setting correct?

If the Paper Size setting and the size of the actual paper do not match, the

print may not be where you want it, or part of it may be cut off. In this case,

check the print settings.

Is the paper skewed?

If PAPER SKEW CHECK in the panel settings is OFF, the paper is printed even if it

is skewed. In this case, the print will not be in the print area. Set PAPER SKEW

CHECK to ON in the Menu mode.

See “PRINTER SETUP” on page 20.

Does the print data fit within the paper width?

If the print image is bigger than the paper width, printing normally stops.

However, if the PAPER SIZE CHECK is OFF, the paper is printed even if the paper

width is exceeded. Set PAPER SIZE CHECK to ON in the Menu mode.

See “PRINTER SETUP” on page 20.

Is the roll paper margin set to 15 mm or 35 mm?

With auto rotation, or if you print to the full width of the paper (printing at A1

vertical size on 24-inch wide roll paper, or printing at A2 horizontal size), if the

ROLL PAPER MARGIN is set to 15 mm or 35 mm, the data extending beyond the

print area on the right side of the paper is not printed. Set ROLL PAPER MARGIN

to 3 mm.

See “PRINTER SETUP” on page 20.

Left/right ruled lines are

bumpy.

Is the print head misaligned (leaving gaps)? (during bidirectional printing)

With bidirectional printing, the print head prints while moving left and right.

If the print head is misaligned, ruled lines may be printed misaligned with

gaps. If vertical ruled lines are misaligned with bidirectional printing, adjust

the gap.

See “Print head alignment” on page 138.

The printed surface is scuffed

or soiled.

Is the paper too thick or too thin?

Check that the paper is a specification that can be used with this printer. For

information about the media types and appropriate settings for printing on

paper from other manufacturers or when using a raster image processor

(RIP), please refer to the handling instructions for the paper, or contact the

retailer of the paper or the manufacturer of the RIP.

Is the print head scuffing the printed surface with thick paper?

When using thick paper, the print head may scuff the printed surface. In this

case, set PLATEN GAP to a point between WIDE and WIDEST.

See “PRINTER SETUP” on page 20.

The paper is creased.

Are you using the printer at normal room temperature?

Epson's special paper should be used at normal room temperature

(temperature: 15 to 25°C, humidity: 40 to 60%). For information about paper

such as thin paper from other manufacturers that requires special handling,

refer to the relevant handling instructions.

When using paper other than Epson special media, have you set the paper

characteristics?

When using paper other than Epson special media, set the paper

characteristics (custom paper) before printing.

See “Printing with Non-Epson Media” on page 100.

Cause What to do

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Epson Stylus Pro 11880C Seite 162

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Epson Stylus Pro 11880C

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info