Bedienungsanleitung Epson SureColor SC-F2000 (Seite 85 von 104) (Englisch)

617671

Zoom out

Zoom in

Vorherige Seite

1/104

Nächste Seite

Platen Height Error is displayed while

printing

Are you printing data over the entire print

area that requires a large amount of ink?

The print surface swells when you print data that

requires a large amount of ink, and it may trigger the

height position sensor. If this occurs, try loading the

T-shirt as shown below.

Have you dried pre-treatment liquid

completely?

The print surface becomes wet and swells if the

pre-treatment liquid is not dried sufficiently before

printing, and it may trigger the height position sensor.

Check that the pre-treatment liquid is dry.

Areas not printed are stained with ink

Is the platen clean?

The platen's frame and the top plate may be stained.

Check the platen and clean it if necessary.

U “Cleaning the Printer” on page 68

Even after cleaning the scale, a

cleaning message is displayed

Is there any dust or ink cleaner on the carriage

scale?

If dust or ink cleaner remain on the carriage scale after

wiping, a cleaning message is displayed. Check that

there is no dust or ink cleaner remaining on the scale.

If this message appears on the LCD panel again,

contact your dealer or Epson Support.

The printer status and log are printed

over the edges of the paper

Are you printing with an M size (standard)

platen?

Depending on the paper size the print area may

extend beyond the edges of the paper if paper is

loaded on an optional platen. Load paper on the M

size (standard) platen, and then print.

U “Loading paper” on page 44

Printing is slow or stops half way

Is the head move direction set to

uni-directional?

Head Move Direction may be set to Uni-Directional

in the printer's Garment Creator software or in the

printer's settings. Set Head Move Direction to

anything except Uni-Directional from the control

panel's menu list.

U “Menu List” on page 70

Are you using a USB memory stick with a slow

reading speed?

If you use a USB memory stick with a slow reading

speed (4.63 MB/sec or less) when printing from a USB

memory stick, the print head stops at times during

printing and printing continues. Use a USB memory

stick with a fast reading speed.

Printing does not start

Is a USB memory stick connected?

When a USB memory stick is connected to the printer,

printing does not start until the data has been saved

to the USB memory stick. Remove the USB memory

stick to speed up the printing process.

Cannot use the USB memory

Have you selected USB File List from the

Settings menu after connecting a USB

memory stick?

The USB memory icon is not displayed on the control

panel by just connecting a USB memory stick. The icon

is displayed when you select USB File List from the

Settings menu and data has been saved, or when data

is transmitted from a computer to the USB memory

stick connected to the printer.

SC-F2000 Series User’s Guide

Problem Solver

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Epson SureColor SC-F2000 Seite 85

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Epson SureColor SC-F2000

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info