Bedienungsanleitung Epson SureColor SC-S50600 (Seite 163 von 198) (Englisch)

617685

163

Zoom out

Zoom in

Vorherige Seite

1/198

Nächste Seite

The printed surface is scuffed or

soiled.

Is the media too thick or too thin?

Check media specifications to confirm that it is

compatible with the printer. If you are using a

software RIP, contact the manufacturer for

information on the settings and media that can be

used.

Is the media wavy?

Certain types of media may develop waves under

some conditions (humidity and temperature) while

installed in the printer. If a wave has developed, press

the d button in the control panel to feed the media

and avoid the affected area. We recommend that you

lower the temperature and humidity to prevent

waves developing.

Is the media creased or folded?

Media that is creased or folded may rise from the

platen and contact the print head, resulting in

smudges or uneven colors.

Are the wiper, caps, or print head stained?

Ink clots, lint or dust around the wiper, caps, or print

head may result in stains caused by ink drops. Clean

the affected area.

U “Cleaning” on page 103

Is the print head striking the printed surface?

If the printed side of the media is scuffed, select Media

Setup - Customize Settings on the control panel to

change Platen Gap according to the currently loaded

media.

If a scuff recurs after Platen Gap has been changed,

increase the value of Media Tension; this symptom

may be improved.

U “Customize Settings” on page 145

When Platen Gap or Media Tension has been

changed, perform Media Adjust again.

U “Media Adjust” on page 86

Areas secured by pressure rollers are

stained.

Are the pressure rollers stained?

Clean the pressure rollers.

U “Cleaning Inside the Printer (Once a week to once

a month)” on page 113

Nozzle clogs cannot be cleared.

Is cleaning being performed regularly?

If lint or dust adheres to the area around the print

head, caps (photo 1), wiper (photo 2), or flushing pad,

nozzle clogs may occur during printing. Moreover, if

the lint or dust is left adhered, nozzle clogs cannot be

cleared even after repeated head cleaning. Also, as

shown in photo (3), if a film of ink has adhered,

capping fails, causing a printing failure.

Clean the affected area periodically.

U “Cleaning” on page 103

Replace consumables.

If the problem persists after Head Cleaning has been

performed several times or regular cleaning has been

performed, the wipers or wiper cleaners may be worn

or deteriorated. We recommend that you replace

them when the following symptoms are detected.

❏ Wiper: The wiper edge remains rough even after

stains were wiped off using the clean-room

wiper. Otherwise, the wiper is cracked.

❏ Wiper cleaner: A film of ink has adhered to the

rear surface of the absorbent section.

U “Replacing the Wiper and Wiper Cleaner” on

page 120

❏ Flushing pad: Ink has adhered to the surface, and

lint or dust cannot be removed.

U “Replacing the Flushing Pad” on page 122

EPSON SC-S70600 series/SC-S50600 series/SC-S30600 series User's Guide

Problem Solver

163

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Epson SureColor SC-S50600 Seite 163

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Epson SureColor SC-S50600

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info