Bedienungsanleitung Epson WorkForce Pro WF-5690DW (Seite 13 von 210) (Englisch)

590240

Zoom out

Zoom in

Vorherige Seite

1/210

Nächste Seite

Setting up/using the product

❏ Do not block or cover the vents and openings in the product.

❏ Use only the type of power source indicated on the product’s label.

❏ Avoid using outlets on the same circuit as photocopiers or air control systems that regularly switch on and off.

❏ Avoid electrical outlets controlled by wall switches or automatic timers.

❏ Keep the entire computer system away from potential sources of electromagnetic interference, such as

loudspeakers or the base units of cordless telephones.

❏ The power-supply cords should be placed to avoid abrasions, cuts, fraying, crimping, and kinking. Do not place

objects on top of the power-supply cords and do not allow the power-supply cords to be stepped on or run over. Be

particularly careful to keep all the power-supply cords straight at the ends and the points where they enter and

leave the transformer.

❏ If you use an extension cord with the product, make sure that the total ampere rating of the devices plugged into

the extension cord does not exceed the cord’s ampere rating. Also, make sure that the total ampere rating of all

devices plugged into the wall outlet does not exceed the wall outlet’s ampere rating.

❏ If you plan to use the product in Germany, the building installation must be protected by a 10 or 16 amp circuit

breaker to provide adequate short-circuit protection and over-current protection for the product.

❏ When connecting the product to a computer or other device with a cable, ensure the correct orientation of the

connectors. Each connector has only one correct orientation. Inserting a connector in the wrong orientation may

damage both devices connected by the cable.

❏ Place the product on a flat, stable surface that extends beyond the base of the product in all directions. The product

will not operate properly if it is tilted at an angle.

❏ When storing or transporting the product, avoid tilting it, placing it vertically, or turning it upside down;

otherwise ink may leak.

❏ Allow spaces behind the product for the cables, and space above the product so that you can fully raise the

document cover.

❏ Leave enough space in front of the product for the paper to be fully ejected.

❏ Avoid places subject to rapid changes in temperature and humidity. Also, keep the product away from direct

sunlight, strong light, or heat sources.

❏ Do not insert objects through the slots in the product.

❏ Do not put your hand inside the product during printing.

❏ Do not touch the white flat cable inside the product.

❏ Do not use aerosol products that contain flammable gases inside or around the product. Doing so may cause

fire.

❏ Do not move the print head by hand; otherwise, you may damage the product.

User’s Guide

Important Instructions

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Epson WorkForce Pro WF-5690DW Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Epson WorkForce Pro WF-5690DW

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info